simple solder selection

oven_control.cpp

@@ -3,6 +3,8 @@
 #include <LiquidCrystal.h>
 #include "profile.h"
 
+
+
 //Pin assignments for SainSmart LCD Keypad Shield
 LiquidCrystal lcd(8, 9, 4, 5, 6, 7);
 DFR_Key keypad;
@@ -16,13 +18,6 @@ OvenCtl::OvenCtl() {
   actual_dt = 0.f;
 
 
-  // timestamps of event beginnings/ends
-  Ts_time_start = 0;
-  Ts_time_end = 0;
-  Tl_time_start = 0;
-  Tl_time_end = 0;
-  Tp_time_start = 0;
-  Tp_time_end = 0;
 
   // thermostat
   set_min = 0;
@@ -30,7 +25,7 @@ OvenCtl::OvenCtl() {
   set_dt_min = 0;
   set_dt_max = 0;
 
-  op_state = OP_CONFIG;
+  oven_mode = OM_CONFIG;
   profile_state = START_STATE;
   error_condition = 0;
   is_oven_heating = false;
@@ -43,10 +38,6 @@ OvenCtl::OvenCtl() {
   lcd.begin(16, 2);
 }
 
-void OvenCtl::reset() {
-  digitalWrite(7, LOW);
-}
-
 
 void OvenCtl::send_state() {
   Serial.write(time & 0xff);
@@ -80,16 +71,23 @@ void OvenCtl::recv_config() {
 }
 
 
-void OvenCtl::dispatch_input_config(int cmd) {
+void OvenCtl::dispatch_remote_cmd(COMMAND cmd) {
-  if (cmd == 255)
+  switch (cmd) {
+    case SEND_CONFIG:
       send_config();
-  else if (cmd == 254)
+      break;
+    case RECV_CONFIG:
       recv_config();
-  else if (cmd == 250)
+      break;
-    reset();
+    case SEND_STATE:
-  else if (cmd == 253)
+      recv_config();
+      break;
+    case RECV_STEPS:
+      break;
+    default:
       ;
   }
+}
 
 void OvenCtl::handle_stand_alone_state() {
     time++;
@@ -112,18 +110,20 @@ void OvenCtl::handle_remote_state() {
  *
  */
 void OvenCtl::loop() {
-  int cmd = -1;
+//   int cmd = -1;
 
-  switch (op_state) {
+  switch (oven_mode) {
-    case OP_CONFIG:
+    case OM_CONFIG:
 //       if (profile.handle_config_state())
 //         set_start_state();
       break;
-    case OP_STAND_ALONE:
+    case OM_CALIBRATION:
+      break;
+    case OM_STAND_ALONE:
 //       if (profile.handle_config_state())
 //         set_start_state();
 //       break;
-    case OP_REMOTE:
+    case OM_REMOTE:
 //       if (profile.handle_config_state())
 //         set_start_state();
       break;
@@ -133,24 +133,13 @@ void OvenCtl::loop() {
 //     set_error_state();
 //   }
 
-  if (Serial.available() > 0) {
+
-    cmd = Serial.read();
-    if (cmd == 255)
-      send_config();
-    else if (cmd == 254)
-      send_state();
-    else if (cmd == 253)
-      recv_config();
-    else if (cmd == 252)
-      reset();
 //     else if (cmd == 251)
 //       set_start_state();
-  }
-
   
 
   control_oven();
-  if (profile_state > 0) {
+  if (oven_mode != OM_CONFIG) {
     print_status();
     delay(1000);
   }
@@ -214,14 +203,17 @@ void OvenCtl::print_status() {
 
 
 void OvenCtl::control_oven() {
-  if (temperature <= set_min + actual_hysteresis && !is_oven_heating) {
+  if (is_oven_heating) {
-    is_oven_heating = true;
+    if (temperature >= set_min + actual_hysteresis) {
-//     Serial.println("Oven turned on");
-  }
-  else if (temperature >= set_min + actual_hysteresis && is_oven_heating) {
       is_oven_heating = false;
     }
   }
+  else {
+    if (temperature <= set_min + actual_hysteresis) {
+      is_oven_heating = true;
+    }
+  }
+}
 
 
 void OvenCtl::set_temp(int min, int max, int dt_min, int dt_max) {

oven_control.h

@@ -7,10 +7,18 @@
 #define OP_STAND_ALONE 1
 #define OP_REMOTE 2*/
 
-enum OP_STATE {
+enum OVEN_MODE {
-  OP_CONFIG,
+  OM_CONFIG,
-  OP_STAND_ALONE,
+  OM_CALIBRATION,
-  OP_REMOTE
+  OM_STAND_ALONE,
+  OM_REMOTE
+};
+
+enum COMMAND {
+  SEND_CONFIG,
+  RECV_CONFIG,
+  SEND_STATE,
+  RECV_STEPS
 };
 
 #define E_DT_MIN 1 // temperature dt too small
@@ -55,19 +63,13 @@ public:
 //   void set_config_state();
 
 private:
+
   // system time, timestamps and temperatures from sensors
   int time; // profile seconds
   int temperature; // actual oven temp
   int last_temperature; // last oven temp
   float actual_dt; // actual difference from last to actual temperatur
 
-  // timestamps of event beginnings/ends
-  int Ts_time_start;
-  int Ts_time_end;
-  int Tl_time_start;
-  int Tl_time_end;
-  int Tp_time_start;
-  int Tp_time_end;
 
   // thermostat
   float set_min;
@@ -84,7 +86,7 @@ private:
 
   // state machine
   unsigned int error_condition;
-  OP_STATE op_state;
+  OVEN_MODE oven_mode;
   PROFILE_STATE profile_state;
   boolean is_oven_heating;
 
@@ -127,13 +129,11 @@ private:
 //   void check_Tp_duration_min();
 //   void check_Tp_duration_max();
 
+  // commands
   void send_state();
   void send_config();
-  void reset();
-
   void recv_config();
-
+  void dispatch_remote_cmd(COMMAND cmd);
-  void dispatch_input_config(int);
 };
 
 #endif

reflowctl_gui.py

@@ -1,4 +1,5 @@
 # -*- coding: utf-8 -*-
+#!/usr/bin/python
 
 import sys, os, random
 
@@ -31,6 +32,7 @@ class Solder(object):
         self.psteps = []
         self.durations = dict()
         self.rates = dict()
+        self.name = None
 
         #start = self.add_state("start", 25)
         #ps = self.add_state("preheat start", 150)
@@ -47,6 +49,12 @@ class Solder(object):
         #self.add_rate((pe, tal), 1)
         #self.add_rate((tal, end), -2)
 
+    def __unicode__(self):
+        return unicode(self.name)
+
+    def __str__(self):
+        return self.name
+
 
     def add_state(self, name, temp):
         s = State(name, temp)
@@ -131,6 +139,7 @@ class Solder(object):
         xmltree = etree.parse(filename)
         root = xmltree.getroot()
         s = Solder()
+        s.name = root[0].attrib["name"]
         for state in root[0].findall("state"):
             s.add_state(state.attrib["name"], int(state.attrib["temperature"]))
         for duration in root[0].findall("duration"):
@@ -147,7 +156,21 @@ class Solder(object):
 
         return s
 
+class SolderListModel(QtCore.QAbstractListModel):
+    def __init__(self, parent=None, *args):
+        """ datain: a list where each item is a row
+        """
+        super(SolderListModel, self).__init__(parent, *args)
+        self.listdata = [Solder.unpack(os.path.join("solder_types", p)) for p in os.listdir("solder_types")]
 
+    def rowCount(self, parent=QtCore.QModelIndex()):
+        return len(self.listdata)
+
+    def data(self, index, role):
+        if index.isValid() and role == QtCore.Qt.DisplayRole:
+            return QtCore.QVariant(self.listdata[index.row()].name)
+        else:
+            return QtCore.QVariant()
 
 class MyDynamicMplCanvas(FigureCanvas):
     """A canvas that updates itself every second with a new plot."""
@@ -293,23 +316,32 @@ class ApplicationWindow(QtGui.QMainWindow):
         self.help_menu.addAction('&About', self.about)
 
         self.main_widget = QtGui.QWidget(self)
+        self.profile_widget = QtGui.QWidget(self)
 
         self.dpi = 100
 
-        #pl = QtGui.QVBoxLayout(self.main_widget)
+        pl = QtGui.QHBoxLayout(self.profile_widget)
-        #self.p
+        self.solder_model = SolderListModel(self)
+        self.solder_view = QtGui.QListView()
+        self.solder_view.setModel(self.solder_model)
+
+        self.connect(self.solder_view, QtCore.SIGNAL("clicked(QModelIndex)"), self.solder_selected)
+        pl.addWidget(self.solder_view)
 
         l = QtGui.QVBoxLayout(self.main_widget)
-        #sc = MyStaticMplCanvas(self.main_widget, width=5, height=4, dpi=100)
         self.dc = MyDynamicMplCanvas(self.main_widget, width=5, height=4, dpi=self.dpi)
-        #l.addWidget(sc)
+        l.addWidget(self.profile_widget, 1)
-        l.addWidget(self.dc)
+        l.addWidget(self.dc, 10)
 
         self.main_widget.setFocus()
         self.setCentralWidget(self.main_widget)
 
         self.statusBar().showMessage("All hail matplotlib!", 2000)
 
+    def solder_selected(self, index):
+        if index.isValid():
+            self.dc.solder = self.solder_model.listdata[index.row()]
+
     def save_plot(self):
         file_choices = "PNG (*.png)|*.png"
 
@@ -326,13 +358,9 @@ class ApplicationWindow(QtGui.QMainWindow):
     def about(self):
         QtGui.QMessageBox.about(self, "About %s" % progname,
 u"""%(prog)s version %(version)s
-Copyright \N{COPYRIGHT SIGN} 2005 Florent Rougon, 2006 Darren Dale
+Copyright \N{COPYRIGHT SIGN} 2012 Stefan Kögl
 
-This program is a simple example of a Qt4 application embedding matplotlib
+reflowctl frontend"""
-canvases.
-
-It may be used and modified with no restriction; raw copies as well as
-modified versions may be distributed without limitation."""
 % {"prog": progname, "version": progversion})