interfisch
/
hoverboard-firmware-hack-foc-serial-esc
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
hoverboard-firmware-hack-fo.../Inc/config.h

464 lines
28 KiB
C
Raw Blame History

// Define to prevent recursive inclusion
#ifndef CONFIG_H
#define CONFIG_H
#include "stm32f1xx_hal.h"
// ############################### VARIANT SELECTION ###############################
// PlatformIO: uncomment desired variant in platformio.ini
// Keil uVision: select desired variant from the Target drop down menu (to the right of the Load button)
// Ubuntu: define the desired build variant here if you want to use make in console
// or use VARIANT environment variable for example like "make -e VARIANT=VARIANT_NUNCHUK". Select only one at a time.
#if !defined(PLATFORMIO)
//#define VARIANT_ADC // Variant for control via ADC input
//#define VARIANT_USART // Variant for Serial control via USART3 input
//#define VARIANT_NUNCHUK // Variant for Nunchuk controlled vehicle build
//#define VARIANT_PPM // Variant for RC-Remote with PPM-Sum Signal
//#define VARIANT_IBUS // Variant for RC-Remotes with FLYSKY IBUS
//#define VARIANT_HOVERCAR // Variant for HOVERCAR build
//#define VARIANT_HOVERBOARD // Variant for HOVERBOARD build
//#define VARIANT_TRANSPOTTER // Variant for TRANSPOTTER build https://github.com/NiklasFauth/hoverboard-firmware-hack/wiki/Build-Instruction:-TranspOtter https://hackaday.io/project/161891-transpotter-ng
#endif
// ########################### END OF VARIANT SELECTION ############################
// ############################### DO-NOT-TOUCH SETTINGS ###############################
#define PWM_FREQ 16000 // PWM frequency in Hz / is also used for buzzer
#define DEAD_TIME 48 // PWM deadtime
#ifdef VARIANT_TRANSPOTTER
#define DELAY_IN_MAIN_LOOP 2
#else
#define DELAY_IN_MAIN_LOOP 5 // in ms. default 5. it is independent of all the timing critical stuff. do not touch if you do not know what you are doing.
#endif
#define TIMEOUT 5 // number of wrong / missing input commands before emergency off
#define A2BIT_CONV 50 // A to bit for current conversion on ADC. Example: 1 A = 50, 2 A = 100, etc
// ADC conversion time definitions
#define ADC_CONV_TIME_1C5 (14) //Total ADC clock cycles / conversion = ( 1.5+12.5)
#define ADC_CONV_TIME_7C5 (20) //Total ADC clock cycles / conversion = ( 7.5+12.5)
#define ADC_CONV_TIME_13C5 (26) //Total ADC clock cycles / conversion = ( 13.5+12.5)
#define ADC_CONV_TIME_28C5 (41) //Total ADC clock cycles / conversion = ( 28.5+12.5)
#define ADC_CONV_TIME_41C5 (54) //Total ADC clock cycles / conversion = ( 41.5+12.5)
#define ADC_CONV_TIME_55C5 (68) //Total ADC clock cycles / conversion = ( 55.5+12.5)
#define ADC_CONV_TIME_71C5 (84) //Total ADC clock cycles / conversion = ( 71.5+12.5)
#define ADC_CONV_TIME_239C5 (252) //Total ADC clock cycles / conversion = (239.5+12.5)
// This settings influences the actual sample-time. Only use definitions above
// This parameter needs to be the same as the ADC conversion for Current Phase of the FIRST Motor in setup.c
#define ADC_CONV_CLOCK_CYCLES (ADC_CONV_TIME_7C5)
// Set the configured ADC divider. This parameter needs to be the same ADC divider as PeriphClkInit.AdcClockSelection (see main.c)
#define ADC_CLOCK_DIV (4)
// ADC Total conversion time: this will be used to offset TIM8 in advance of TIM1 to align the Phase current ADC measurement
// This parameter is used in setup.c
#define ADC_TOTAL_CONV_TIME (ADC_CLOCK_DIV * ADC_CONV_CLOCK_CYCLES) // = ((SystemCoreClock / ADC_CLOCK_HZ) * ADC_CONV_CLOCK_CYCLES), where ADC_CLOCK_HZ = SystemCoreClock/ADC_CLOCK_DIV
// ########################### END OF DO-NOT-TOUCH SETTINGS ############################
// ############################### BATTERY ###############################
/* Battery voltage calibration: connect power source.
* see How to calibrate.
* Write debug output value nr 5 to BAT_CALIB_ADC. make and flash firmware.
* Then you can verify voltage on debug output value 6 (to get calibrated voltage multiplied by 100).
*/
#define BAT_FILT_COEF 655 // battery voltage filter coefficient in fixed-point. coef_fixedPoint = coef_floatingPoint * 2^16. In this case 655 = 0.01 * 2^16
#define BAT_CALIB_REAL_VOLTAGE 3970 // input voltage measured by multimeter (multiplied by 100). In this case 43.00 V * 100 = 4300
#define BAT_CALIB_ADC 1492 // adc-value measured by mainboard (value nr 5 on UART debug output)
#define BAT_CELLS 10 // battery number of cells. Normal Hoverboard battery: 10s
#define BAT_LOW_LVL1_ENABLE 0 // to beep or not to beep, 1 or 0
#define BAT_LOW_LVL2_ENABLE 1 // to beep or not to beep, 1 or 0
#define BAT_LOW_LVL1 (360 * BAT_CELLS * BAT_CALIB_ADC) / BAT_CALIB_REAL_VOLTAGE // gently beeps at this voltage level. [V*100/cell]. In this case 3.60 V/cell
#define BAT_LOW_LVL2 (350 * BAT_CELLS * BAT_CALIB_ADC) / BAT_CALIB_REAL_VOLTAGE // your battery is almost empty. Charge now! [V*100/cell]. In this case 3.50 V/cell
#define BAT_LOW_DEAD (337 * BAT_CELLS * BAT_CALIB_ADC) / BAT_CALIB_REAL_VOLTAGE // undervoltage poweroff. (while not driving) [V*100/cell]. In this case 3.37 V/cell
// ######################## END OF BATTERY ###############################
// ############################### TEMPERATURE ###############################
/* Board overheat detection: the sensor is inside the STM/GD chip.
* It is very inaccurate without calibration (up to 45°C). So only enable this funcion after calibration!
* Let your board cool down.
* see <How to calibrate.
* Get the real temp of the chip by thermo cam or another temp-sensor taped on top of the chip and write it to TEMP_CAL_LOW_DEG_C.
* Write debug output value 8 to TEMP_CAL_LOW_ADC. drive around to warm up the board. it should be at least 20°C warmer. repeat it for the HIGH-values.
* Enable warning and/or poweroff and make and flash firmware.
*/
#define TEMP_FILT_COEF 655 // temperature filter coefficient in fixed-point. coef_fixedPoint = coef_floatingPoint * 2^16. In this case 655 = 0.01 * 2^16
#define TEMP_CAL_LOW_ADC 1655 // temperature 1: ADC value
#define TEMP_CAL_LOW_DEG_C 358 // temperature 1: measured temperature [°C * 10]. Here 35.8 °C
#define TEMP_CAL_HIGH_ADC 1588 // temperature 2: ADC value
#define TEMP_CAL_HIGH_DEG_C 489 // temperature 2: measured temperature [°C * 10]. Here 48.9 °C
#define TEMP_WARNING_ENABLE 0 // to beep or not to beep, 1 or 0, DO NOT ACTIVITE WITHOUT CALIBRATION!
#define TEMP_WARNING 600 // annoying fast beeps [°C * 10]. Here 60.0 °C
#define TEMP_POWEROFF_ENABLE 0 // to poweroff or not to poweroff, 1 or 0, DO NOT ACTIVITE WITHOUT CALIBRATION!
#define TEMP_POWEROFF 650 // overheat poweroff. (while not driving) [°C * 10]. Here 65.0 °C
// ######################## END OF TEMPERATURE ###############################
// ############################### MOTOR CONTROL #########################
/* GENERAL NOTES:
* 1. The parameters here are over-writing the default motor parameters. For all the available parameters check BLDC_controller_data.c
* 2. The parameters are represented in fixed point data type for a more efficient code execution
* 3. For calibrating the fixed-point parameters use the Fixed-Point Viewer tool (see <https://github.com/EmanuelFeru/FixedPointViewer>)
* 4. For more details regarding the parameters and the working principle of the controller please consult the Simulink model
* 5. A webview was created, so Matlab/Simulink installation is not needed, unless you want to regenerate the code.
* The webview is an html page that can be opened with browsers like: Microsoft Internet Explorer or Microsoft Edge
*
* NOTES Field Weakening / Phase Advance:
* 1. The Field Weakening is a linear interpolation from 0 to FIELD_WEAK_MAX or PHASE_ADV_MAX (depeding if FOC or SIN is selected, respectively)
* 2. The Field Weakening starts engaging at FIELD_WEAK_LO and reaches the maximum value at FIELD_WEAK_HI
* 3. If you re-calibrate the Field Weakening please take all the safety measures! The motors can spin very fast!
Inputs:
- cmd1 and cmd2: analog normalized input values. INPUT_MIN to INPUT_MAX
- button1 and button2: digital input values. 0 or 1
- adc_buffer.l_tx2 and adc_buffer.l_rx2: unfiltered ADC values (you do not need them). 0 to 4095
Outputs:
- speedR and speedL: normal driving INPUT_MIN to INPUT_MAX
*/
// Control selections
#define CTRL_TYP_SEL 2 // [-] Control type selection: 0 = Commutation , 1 = Sinusoidal, 2 = FOC Field Oriented Control (default)
#define CTRL_MOD_REQ 1 // [-] Control mode request: 0 = Open mode, 1 = VOLTAGE mode (default), 2 = SPEED mode, 3 = TORQUE mode. Note: SPEED and TORQUE modes are only available for FOC!
#define DIAG_ENA 1 // [-] Motor Diagnostics enable flag: 0 = Disabled, 1 = Enabled (default)
// Limitation settings
#define I_MOT_MAX 15 // [A] Maximum motor current limit
#define I_DC_MAX 17 // [A] Maximum DC Link current limit (This is the final current protection. Above this value, current chopping is applied. To avoid this make sure that I_DC_MAX = I_MOT_MAX + 2A)
#define N_MOT_MAX 1000 // [rpm] Maximum motor speed limit
// Field Weakening / Phase Advance
#define FIELD_WEAK_ENA 0 // [-] Field Weakening / Phase Advance enable flag: 0 = Disabled (default), 1 = Enabled
#define FIELD_WEAK_MAX 5 // [A] Maximum Field Weakening D axis current (only for FOC). Higher current results in higher maximum speed.
#define PHASE_ADV_MAX 25 // [deg] Maximum Phase Advance angle (only for SIN). Higher angle results in higher maximum speed.
#define FIELD_WEAK_HI 1500 // [-] Input target High threshold for reaching maximum Field Weakening / Phase Advance. Do NOT set this higher than 1500.
#define FIELD_WEAK_LO 1000 // [-] Input target Low threshold for starting Field Weakening / Phase Advance. Do NOT set this higher than 1000.
// Data checks - Do NOT touch
#if (FIELD_WEAK_ENA == 0)
#undef FIELD_WEAK_HI
#define FIELD_WEAK_HI 1000 // [-] This prevents the input target going beyond 1000 when Field Weakening is not enabled
#endif
#define INPUT_MAX MAX( 1000, FIELD_WEAK_HI) // [-] Defines the Input target maximum limitation
#define INPUT_MIN MIN(-1000,-FIELD_WEAK_HI) // [-] Defines the Input target minimum limitation
#define INPUT_MID INPUT_MAX / 2
// ########################### END OF MOTOR CONTROL ########################
// ############################## DEFAULT SETTINGS ############################
// Default settings will be applied at the end of this config file if not set before
#define INACTIVITY_TIMEOUT 8 // Minutes of not driving until poweroff. it is not very precise.
#define BEEPS_BACKWARD 1 // 0 or 1
// #define SUPPORT_BUTTONS // Define for buttons support on ADC, Nunchuck
/* FILTER is in fixdt(0,16,16): VAL_fixedPoint = VAL_floatingPoint * 2^16. In this case 6553 = 0.1 * 2^16
* Value of COEFFICIENT is in fixdt(1,16,14)
* If VAL_floatingPoint >= 0, VAL_fixedPoint = VAL_floatingPoint * 2^14
* If VAL_floatingPoint < 0, VAL_fixedPoint = 2^16 + floor(VAL_floatingPoint * 2^14).
*/
// Value of RATE is in fixdt(1,16,4): VAL_fixedPoint = VAL_floatingPoint * 2^4. In this case 480 = 30 * 2^4
#define DEFAULT_RATE 480 // 30.0f [-] lower value == slower rate [0, 32767] = [0.0, 2047.9375]. Do NOT make rate negative (>32767)
#define DEFAULT_FILTER 6553 // Default for FILTER 0.1f [-] lower value == softer filter [0, 65535] = [0.0 - 1.0].
#define DEFAULT_SPEED_COEFFICIENT 16384 // Default for SPEED_COEFFICIENT 1.0f [-] higher value == stronger. [0, 65535] = [-2.0 - 2.0]. In this case 16384 = 1.0 * 2^14
#define DEFAULT_STEER_COEFFICIENT 8192 // Defualt for STEER_COEFFICIENT 0.5f [-] higher value == stronger. [0, 65535] = [-2.0 - 2.0]. In this case 8192 = 0.5 * 2^14. If you do not want any steering, set it to 0.
// ######################### END OF DEFAULT SETTINGS ##########################
// ############################### DEBUG SERIAL ###############################
/* Connect GND and RX of a 3.3v uart-usb adapter to the left (USART2) or right sensor board cable (USART3)
* Be careful not to use the red wire of the cable. 15v will destroye evrything.
* If you are using VARIANT_NUNCHUK, disable it temporarily.
* enable DEBUG_SERIAL_USART3 or DEBUG_SERIAL_USART2
* and DEBUG_SERIAL_ASCII use asearial terminal.
*
*
* DEBUG_SERIAL_ASCII output is:
* // "1:345 2:1337 3:0 4:0 5:0 6:0 7:0 8:0\r\n"
*
* 1: (int16_t)adc_buffer.l_tx2); ADC1
* 2: (int16_t)adc_buffer.l_rx2); ADC2
* 3: (int16_t)speedR); output command: [-1000, 1000]
* 4: (int16_t)speedL); output command: [-1000, 1000]
* 5: (int16_t)adc_buffer.batt1); Battery adc-value measured by mainboard
* 6: (int16_t)(batVoltage * BAT_CALIB_REAL_VOLTAGE / BAT_CALIB_ADC)); Battery calibrated voltage multiplied by 100 for verifying battery voltage calibration
* 7: (int16_t)board_temp_adcFilt); for board temperature calibration
* 8: (int16_t)board_temp_deg_c); Temperature in celcius for verifying board temperature calibration
*
*/
// #define DEBUG_SERIAL_USART2 // left sensor board cable, disable if ADC or PPM is used!
#if defined(VARIANT_ADC) || defined(VARIANT_HOVERCAR)
#define DEBUG_SERIAL_USART3 // right sensor board cable, disable if I2C (nunchuk or lcd) is used!
#endif
#ifndef VARIANT_TRANSPOTTER
//#define DEBUG_SERIAL_SERVOTERM
#define DEBUG_SERIAL_ASCII
#endif
// ########################### END OF DEBUG SERIAL ############################
// ############################### DEBUG LCD ###############################
//#define DEBUG_I2C_LCD // standard 16x2 or larger text-lcd via i2c-converter on right sensor board cable
// ########################### END OF DEBUG LCD ############################
// ################################# VARIANT_ADC SETTINGS ############################
#ifdef VARIANT_ADC
/* CONTROL VIA TWO POTENTIOMETERS
* ADC-calibration to cover the full poti-range:
* Connect potis to left sensor board cable (0 to 3.3V) (do NOT use the red 15V wire in the cable!). see <How to calibrate>.
* Turn the potis to minimum position, write value 1 to ADC1_MIN and value 2 to ADC2_MIN
* Turn the potis to maximum position, write value 1 to ADC1_MAX and value 2 to ADC2_MAX
* For middle resting potis: Let the potis in the middle resting position, write value 1 to ADC1_MID and value 2 to ADC2_MID
* Make, flash and test it.
*/
#define CONTROL_ADC // use ADC as input. disable CONTROL_SERIAL_USART2, FEEDBACK_SERIAL_USART2, DEBUG_SERIAL_USART2!
// #define ADC_PROTECT_ENA // ADC Protection Enable flag. Use this flag to make sure the ADC is protected when GND or Vcc wire is disconnected
#define ADC_PROTECT_TIMEOUT 30 // ADC Protection: number of wrong / missing input commands before safety state is taken
#define ADC_PROTECT_THRESH 400 // ADC Protection threshold below/above the MIN/MAX ADC values
// #define ADC1_MID_POT // ADC1 middle resting poti: comment-out if NOT a middle resting poti
#define ADC1_MIN 0 // min ADC1-value while poti at minimum-position (0 - 4095)
#define ADC1_MID 2048 // mid ADC1-value while poti at minimum-position (ADC1_MIN - ADC1_MAX)
#define ADC1_MAX 4095 // max ADC1-value while poti at maximum-position (0 - 4095)
// #define ADC2_MID_POT // ADC2 middle resting poti: comment-out if NOT a middle resting poti
#define ADC2_MIN 0 // min ADC2-value while poti at minimum-position (0 - 4095)
#define ADC2_MID 2048 // mid ADC2-value while poti at minimum-position (ADC2_MIN - ADC2_MAX)
#define ADC2_MAX 4095 // max ADC2-value while poti at maximum-position (0 - 4095)
#endif
// ############################# END OF VARIANT_ADC SETTINGS #########################
// ############################ VARIANT_USART SETTINGS ############################
#ifdef VARIANT_USART
// #define CONTROL_SERIAL_USART2 // left sensor board cable, disable if ADC or PPM is used! For Arduino control check the hoverSerial.ino
// #define FEEDBACK_SERIAL_USART2 // left sensor board cable, disable if ADC or PPM is used!
#define CONTROL_SERIAL_USART3 // right sensor board cable, disable if I2C (nunchuk or lcd) is used! For Arduino control check the hoverSerial.ino
#define FEEDBACK_SERIAL_USART3 // right sensor board cable, disable if I2C (nunchuk or lcd) is used!
#endif
// ######################## END OF VARIANT_USART SETTINGS #########################
// ################################# VARIANT_NUNCHUK SETTINGS ############################
#ifdef VARIANT_NUNCHUK
/* left sensor board cable. USART3
* keep cable short, use shielded cable, use ferrits, stabalize voltage in nunchuk,
* use the right one of the 2 types of nunchuks, add i2c pullups.
* use original nunchuk. most clones does not work very well.
* Recommendation: Nunchuk Breakout Board https://github.com/Jan--Henrik/hoverboard-breakout
*/
#define CONTROL_NUNCHUK // use nunchuk as input. disable FEEDBACK_SERIAL_USART3, DEBUG_SERIAL_USART3!
// # maybe good for ARMCHAIR #
#define FILTER 3276 // 0.05f
#define SPEED_COEFFICIENT 8192 // 0.5f
#define STEER_COEFFICIENT 62259 // -0.2f
#endif
// ############################# END OF VARIANT_NUNCHUK SETTINGS #########################
// ################################# VARIANT_PPM SETTINGS ##############################
#ifdef VARIANT_PPM
/* ###### CONTROL VIA RC REMOTE ######
* left sensor board cable. Channel 1: steering, Channel 2: speed.
* https://gist.github.com/peterpoetzi/1b63a4a844162196613871767189bd05
*/
#define CONTROL_PPM // use PPM-Sum as input. disable CONTROL_SERIAL_USART2!
#define PPM_NUM_CHANNELS 6 // total number of PPM channels to receive, even if they are not used.
#endif
// ############################# END OF VARIANT_PPM SETTINGS ############################
// ################################# VARIANT_IBUS SETTINGS ##############################
#ifdef VARIANT_IBUS
/* CONTROL VIA RC REMOTE WITH FLYSKY IBUS PROTOCOL
* Connected to Left sensor board cable. Channel 1: steering, Channel 2: speed.
*/
#define CONTROL_IBUS // use IBUS as input
#define IBUS_NUM_CHANNELS 14 // total number of IBUS channels to receive, even if they are not used.
#define IBUS_LENGTH 0x20
#define IBUS_COMMAND 0x40
#undef USART2_BAUD
#define USART2_BAUD 115200
#define CONTROL_SERIAL_USART2 // left sensor board cable, disable if ADC or PPM is used!
#define FEEDBACK_SERIAL_USART2 // left sensor board cable, disable if ADC or PPM is used!
#endif
// ############################# END OF VARIANT_IBUS SETTINGS ############################
// ############################ VARIANT_HOVERCAR SETTINGS ############################
#ifdef VARIANT_HOVERCAR
#define CONTROL_ADC // use ADC as input. disable CONTROL_SERIAL_USART2, FEEDBACK_SERIAL_USART2, DEBUG_SERIAL_USART2!
#define ADC_PROTECT_ENA // ADC Protection Enable flag. Use this flag to make sure the ADC is protected when GND or Vcc wire is disconnected
#define ADC_PROTECT_TIMEOUT 30 // ADC Protection: number of wrong / missing input commands before safety state is taken
#define ADC_PROTECT_THRESH 400 // ADC Protection threshold below/above the MIN/MAX ADC values
#define ADC1_MIN 1000 // min ADC1-value while poti at minimum-position (0 - 4095)
#define ADC1_MAX 2500 // max ADC1-value while poti at maximum-position (0 - 4095)
#define ADC2_MIN 500 // min ADC2-value while poti at minimum-position (0 - 4095)
#define ADC2_MAX 2200 // max ADC2-value while poti at maximum-position (0 - 4095)
#define SPEED_COEFFICIENT 16384 // 1.0f
#define STEER_COEFFICIENT 0 // 0.0f
//#define INVERT_R_DIRECTION // Invert rotation of right motor
//#define INVERT_L_DIRECTION // Invert rotation of left motor
#endif
// Multiple tap detection: default DOUBLE Tap on Brake pedal (4 pulses)
#define MULTIPLE_TAP_NR 2 * 2 // [-] Define tap number: MULTIPLE_TAP_NR = number_of_taps * 2, number_of_taps = 1 (for single taping), 2 (for double tapping), 3 (for triple tapping), etc...
#define MULTIPLE_TAP_HI 600 // [-] Multiple tap detection High hysteresis threshold
#define MULTIPLE_TAP_LO 200 // [-] Multiple tap detection Low hysteresis threshold
#define MULTIPLE_TAP_TIMEOUT 2000 // [ms] Multiple tap detection Timeout period. The taps need to happen within this time window to be accepted.
// ######################## END OF VARIANT_HOVERCAR SETTINGS #########################
// ############################ VARIANT_HOVERBOARD SETTINGS ############################
// ##### ! NOT IMPLEMENTED YET ! #####
#ifdef VARIANT_HOVERBOARD
// #define CONTROL_SERIAL_USART2 // left sensor board cable, disable if ADC or PPM is used! For Arduino control check the hoverSerial.ino
// #define FEEDBACK_SERIAL_USART2 // left sensor board cable, disable if ADC or PPM is used!
#define CONTROL_SERIAL_USART3 // right sensor board cable, disable if I2C (nunchuk or lcd) is used! For Arduino control check the hoverSerial.ino
#define FEEDBACK_SERIAL_USART3 // right sensor board cable, disable if I2C (nunchuk or lcd) is used!
#endif
// ######################## END OF VARIANT_HOVERBOARD SETTINGS #########################
// ################################# VARIANT_TRANSPOTTER SETTINGS ############################
//TODO ADD VALIDATION
#ifdef VARIANT_TRANSPOTTER
#define CONTROL_GAMETRAK
#define SUPPORT_LCD
// #define SUPPORT_NUNCHUK
#define GAMETRAK_CONNECTION_NORMAL // for normal wiring according to the wiki instructions
//#define GAMETRAK_CONNECTION_ALTERNATE // use this define instead if you messed up the gametrak ADC wiring (steering is speed, and length of the wire is steering)
#define ROT_P 1.2 // P coefficient for the direction controller. Positive / Negative values to invert gametrak steering direction.
// during nunchuk control (only relevant when activated)
#define SPEED_COEFFICIENT 14746 // 0.9f - higher value == stronger. 0.0 to ~2.0?
#define STEER_COEFFICIENT 8192 // 0.5f - higher value == stronger. if you do not want any steering, set it to 0.0; 0.0 to 1.0
#define INVERT_R_DIRECTION // Invert right motor
#define INVERT_L_DIRECTION // Invert left motor
#endif
// ############################# END OF VARIANT_TRANSPOTTER SETTINGS ########################
// ########################### UART SETIINGS ############################
#if defined(FEEDBACK_SERIAL_USART2) || defined(CONTROL_SERIAL_USART2) || defined(DEBUG_SERIAL_USART2) || \
defined(FEEDBACK_SERIAL_USART3) || defined(CONTROL_SERIAL_USART3) || defined(DEBUG_SERIAL_USART3)
#define START_FRAME 0xAAAA // [-] Start frame definition for serial commands
#define SERIAL_TIMEOUT 160 // [-] Serial timeout duration for the received data. 160 ~= 0.8 sec. Calculation: 0.8 sec / 0.005 sec
#endif
#if defined(FEEDBACK_SERIAL_USART2) || defined(CONTROL_SERIAL_USART2) || defined(DEBUG_SERIAL_USART2)
#ifndef USART2_BAUD
#define USART2_BAUD 38400 // UART2 baud rate (long wired cable)
#endif
#define USART2_WORDLENGTH UART_WORDLENGTH_8B // UART_WORDLENGTH_8B or UART_WORDLENGTH_9B
#endif
#if defined(FEEDBACK_SERIAL_USART3) || defined(CONTROL_SERIAL_USART3) || defined(DEBUG_SERIAL_USART3)
#define USART3_BAUD 38400 // UART3 baud rate (short wired cable)
#define USART3_WORDLENGTH UART_WORDLENGTH_8B // UART_WORDLENGTH_8B or UART_WORDLENGTH_9B
#endif
#if defined(FEEDBACK_SERIAL_USART2) || defined(DEBUG_SERIAL_USART2)
#define UART_DMA_CHANNEL DMA1_Channel7
#endif
#if defined(FEEDBACK_SERIAL_USART3) || defined(DEBUG_SERIAL_USART3)
#define UART_DMA_CHANNEL DMA1_Channel2
#endif
// ########################### UART SETIINGS ############################
// ############################### APPLY DEFAULT SETTINGS ###############################
#ifndef RATE
#define RATE DEFAULT_RATE
#endif
#ifndef FILTER
#define FILTER DEFAULT_FILTER
#endif
#ifndef SPEED_COEFFICIENT
#define SPEED_COEFFICIENT DEFAULT_SPEED_COEFFICIENT
#endif
#ifndef STEER_COEFFICIENT
#define STEER_COEFFICIENT DEFAULT_STEER_COEFFICIENT
#endif
// ########################### END OF APPLY DEFAULT SETTING ############################
// ############################### VALIDATE SETTINGS ###############################
#if !defined(VARIANT_ADC) && !defined(VARIANT_USART) && !defined(VARIANT_NUNCHUK) && !defined(VARIANT_PPM) && !defined(VARIANT_IBUS) && \
!defined(VARIANT_HOVERCAR) && !defined(VARIANT_HOVERBOARD) && !defined(VARIANT_TRANSPOTTER)
#error Variant not defined! Please check platformio.ini or Inc/config.h for available variants.
#endif
#if defined(CONTROL_SERIAL_USART2) && defined(CONTROL_SERIAL_USART3)
#error CONTROL_SERIAL_USART2 and CONTROL_SERIAL_USART3 not allowed, choose one.
#endif
#if defined(FEEDBACK_SERIAL_USART2) && defined(FEEDBACK_SERIAL_USART3)
#error FEEDBACK_SERIAL_USART2 and FEEDBACK_SERIAL_USART3 not allowed, choose one.
#endif
#if defined(DEBUG_SERIAL_USART2) && defined(FEEDBACK_SERIAL_USART2)
#error DEBUG_SERIAL_USART2 and FEEDBACK_SERIAL_USART2 not allowed, choose one.
#endif
#if defined(DEBUG_SERIAL_USART3) && defined(FEEDBACK_SERIAL_USART3)
#error DEBUG_SERIAL_USART3 and FEEDBACK_SERIAL_USART3 not allowed, choose one.
#endif
#if defined(DEBUG_SERIAL_USART2) && defined(DEBUG_SERIAL_USART3)
#error DEBUG_SERIAL_USART2 and DEBUG_SERIAL_USART3 not allowed, choose one.
#endif
#if defined(CONTROL_ADC) && (defined(CONTROL_SERIAL_USART2) || defined(FEEDBACK_SERIAL_USART2) || defined(DEBUG_SERIAL_USART2))
#error CONTROL_ADC and SERIAL_USART2 not allowed. It is on the same cable.
#endif
#if (defined(DEBUG_SERIAL_USART2) || defined(CONTROL_SERIAL_USART2)) && defined(CONTROL_PPM)
#error CONTROL_PPM and SERIAL_USART2 not allowed. It is on the same cable.
#endif
#if (defined(DEBUG_SERIAL_USART3) || defined(CONTROL_SERIAL_USART3)) && defined(CONTROL_NUNCHUK)
#error CONTROL_NUNCHUK and SERIAL_USART3 not allowed. It is on the same cable.
#endif
#if (defined(DEBUG_SERIAL_USART3) || defined(CONTROL_SERIAL_USART3)) && defined(DEBUG_I2C_LCD)
#error DEBUG_I2C_LCD and SERIAL_USART3 not allowed. It is on the same cable.
#endif
#if defined(CONTROL_PPM) && defined(CONTROL_ADC) && defined(CONTROL_NUNCHUK) || defined(CONTROL_PPM) && defined(CONTROL_ADC) || defined(CONTROL_ADC) && defined(CONTROL_NUNCHUK) || defined(CONTROL_PPM) && defined(CONTROL_NUNCHUK)
#error only 1 input method allowed. use CONTROL_PPM or CONTROL_ADC or CONTROL_NUNCHUK.
#endif
#if defined(ADC_PROTECT_ENA) && ((ADC1_MIN - ADC_PROTECT_THRESH) <= 0 || (ADC1_MAX + ADC_PROTECT_THRESH) >= 4096)
#warning ADC1 Protection NOT possible! Adjust the ADC thresholds.
#undef ADC_PROTECT_ENA
#endif
#if defined(ADC_PROTECT_ENA) && ((ADC2_MIN - ADC_PROTECT_THRESH) <= 0 || (ADC2_MAX + ADC_PROTECT_THRESH) >= 4096)
#warning ADC2 Protection NOT possible! Adjust the ADC thresholds.
#undef ADC_PROTECT_ENA
#endif
#if defined(CONTROL_PPM) && !defined(PPM_NUM_CHANNELS)
#error Total number of PPM channels needs to be set
#endif
// ############################# END OF VALIDATE SETTINGS ############################
#endif
Reference in New Issue View Git Blame Copy Permalink