hoverboard-firmware-hack-fo.../platformio.ini

180 lines
4.9 KiB
INI

; PlatformIO Project Configuration File2
; http://docs.platformio.org/page/projectconf.html
[platformio]
include_dir = Inc
src_dir = Src
;=================== VARIANT SELECTION ==========================
;
; Choose one or all variants get built
;
;default_envs = VARIANT_ADC ; Variant for control via ADC input
;default_envs = VARIANT_USART3 ; Variant for Serial control via USART3 input
;default_envs = VARIANT_NUNCHUCK ; Variant for Nunchuck controlled vehicle build
;default_envs = VARIANT_PPM ; Variant for RC-Remotes with PPM-Sum signal
;default_envs = VARIANT_IBUS ; Variant for RC-Remotes with FLYSKY IBUS
;default_envs = VARIANT_HOVERCAR ; Variant for HOVERCAR build
;default_envs = VARIANT_TRANSPOTTER ; Variant for TRANSPOTTER build https://github.com/NiklasFauth/hoverboard-firmware-hack/wiki/Build-Instruction:-TranspOtter https://hackaday.io/project/161891-transpotter-ng
;================================================================
;================================================================
[env:VARIANT_ADC]
platform = ststm32
framework = stm32cube
board = genericSTM32F103RC
debug_tool = stlink
upload_protocol = stlink
; Serial Port settings (make sure the COM port is correct)
monitor_port = COM5
monitor_speed = 38400
build_flags =
-I${PROJECT_DIR}/inc/
-DUSE_HAL_DRIVER
-DSTM32F103xE
-Wl,-T./STM32F103RCTx_FLASH.ld
-Wl,-lc
-Wl,-lm
-g -ggdb ; to generate correctly the 'firmware.elf' for STM STUDIO vizualization
# -Wl,-lnosys
-D VARIANT_ADC
-D PLATFORMIO
;================================================================
[env:VARIANT_USART3]
platform = ststm32
framework = stm32cube
board = genericSTM32F103RC
debug_tool = stlink
upload_protocol = stlink
; Serial Port settings (make sure the COM port is correct)
monitor_port = COM5
monitor_speed = 38400
build_flags =
-I${PROJECT_DIR}/inc/
-DUSE_HAL_DRIVER
-DSTM32F103xE
-Wl,-T./STM32F103RCTx_FLASH.ld
-Wl,-lc
-Wl,-lm
-g -ggdb ; to generate correctly the 'firmware.elf' for STM STUDIO vizualization
# -Wl,-lnosys
-D VARIANT_USART3
-D PLATFORMIO
;================================================================
[env:VARIANT_NUNCHUCK]
platform = ststm32
framework = stm32cube
board = genericSTM32F103RC
debug_tool = stlink
upload_protocol = stlink
build_flags =
-I${PROJECT_DIR}/inc/
-DUSE_HAL_DRIVER
-DSTM32F103xE
-Wl,-T./STM32F103RCTx_FLASH.ld
-Wl,-lc
-Wl,-lm
-g -ggdb ; to generate correctly the 'firmware.elf' for STM STUDIO vizualization
# -Wl,-lnosys
-D VARIANT_NUNCHUCK
-D PLATFORMIO
;================================================================
[env:VARIANT_PPM]
platform = ststm32
framework = stm32cube
board = genericSTM32F103RC
debug_tool = stlink
upload_protocol = stlink
build_flags =
-I${PROJECT_DIR}/inc/
-DUSE_HAL_DRIVER
-DSTM32F103xE
-Wl,-T./STM32F103RCTx_FLASH.ld
-Wl,-lc
-Wl,-lm
-g -ggdb ; to generate correctly the 'firmware.elf' for STM STUDIO vizualization
# -Wl,-lnosys
-D VARIANT_PPM
-D PLATFORMIO
;================================================================
[env:VARIANT_IBUS]
platform = ststm32
framework = stm32cube
board = genericSTM32F103RC
debug_tool = stlink
upload_protocol = stlink
build_flags =
-I${PROJECT_DIR}/inc/
-DUSE_HAL_DRIVER
-DSTM32F103xE
-Wl,-T./STM32F103RCTx_FLASH.ld
-Wl,-lc
-Wl,-lm
-g -ggdb ; to generate correctly the 'firmware.elf' for STM STUDIO vizualization
# -Wl,-lnosys
-D VARIANT_IBUS
-D PLATFORMIO
;================================================================
[env:VARIANT_HOVERCAR]
platform = ststm32
framework = stm32cube
board = genericSTM32F103RC
debug_tool = stlink
upload_protocol = stlink
; Serial Port settings (make sure the COM port is correct)
monitor_port = COM5
monitor_speed = 38400
build_flags =
-I${PROJECT_DIR}/inc/
-DUSE_HAL_DRIVER
-DSTM32F103xE
-Wl,-T./STM32F103RCTx_FLASH.ld
-Wl,-lc
-Wl,-lm
-g -ggdb ; to generate correctly the 'firmware.elf' for STM STUDIO vizualization
# -Wl,-lnosys
-D VARIANT_HOVERCAR
-D PLATFORMIO
;================================================================
[env:VARIANT_TRANSPOTTER]
platform = ststm32
framework = stm32cube
board = genericSTM32F103RC
debug_tool = stlink
upload_protocol = stlink
build_flags =
-I${PROJECT_DIR}/inc/
-DUSE_HAL_DRIVER
-DSTM32F103xE
-Wl,-T./STM32F103RCTx_FLASH.ld
-Wl,-lc
-Wl,-lm
-g -ggdb ; to generate correctly the 'firmware.elf' for STM STUDIO vizualization
# -Wl,-lnosys
-D VARIANT_TRANSPOTTER
-D PLATFORMIO
;================================================================