remove automatic calibration

include/ec.h

@@ -4,12 +4,8 @@
 #include <Arduino.h>
 
 #define EC_PIN_RELAY_PROBE 27
-#define EC_PIN_RELAY_CALIBRATION 26
 #define EC_PIN_RELAY_RANGE 25
 
-#define EC_CALIBRATION_RESISTOR_NC 100000
-#define EC_CALIBRATION_RESISTOR_NO 1000
-
 
 #define EC_PIN_ADC 4
 #define EC_PIN_FREQ 5
@@ -17,37 +13,155 @@
 #define EC_RESOLUTION 8
 #define EC_FREQUENCY 5000
 
-#define EC_ARRAY_SIZE 1024
+#define EC_ARRAY_SIZE 128
-uint16_t ec_array[EC_ARRAY_SIZE];
+uint16_t ec_array_rangeLow[EC_ARRAY_SIZE];
-uint16_t ec_array_pos=0;
+uint16_t ec_array_rangeHigh[EC_ARRAY_SIZE];
-unsigned long last_read_ec=0;
+uint16_t ec_array_pos=EC_ARRAY_SIZE*2;
-#define EC_READ_INTERVAL 1
+#define EC_MEASUREMENT_INTERVAL 10000 //complete filtered measurement every x ms
+  //One filtered measurement takes EC_READ_INTERVAL*EC_ARRAY_SIZE*2
+#define EC_READ_INTERVAL 5 //interval of reading adc value inside a measurement
+
+#define EC_RELAY_SWITCH_SETTLETIME 500  //time until voltage of ec circuit has settled
+
+unsigned long ec_last_change_relay=0; //millis of last relay change
+
+enum ECState{IDLE,MEASURE};
+
+ECState ecstate=IDLE;
+
+
+bool ec_measurementReady();
+void ec_startMeasurement();
+void ec_setRange(bool);
+void ec_connectProbe(bool);
+void ec_releaseRelay();
 
 void ec_setup() {
   pinMode(EC_PIN_ADC,INPUT);
 
   ledcSetup(EC_PWM_CH, EC_FREQUENCY, EC_RESOLUTION);
   ledcAttachPin(EC_PIN_FREQ, EC_PWM_CH);
-  ledcWrite(EC_PWM_CH, 127);
+  ledcWrite(EC_PWM_CH, 127); //50% duty cycle
 
   pinMode(EC_PIN_RELAY_PROBE,OUTPUT); //LOW=Calibration/idle, HIGH=Probe connected
-  pinMode(EC_PIN_RELAY_CALIBRATION,OUTPUT); //LOW=NC Calibration Resistor, HIGH=NO Calib. Res.
   pinMode(EC_PIN_RELAY_RANGE,OUTPUT); //LOW=NC Range Resistor, HIGH=NO Range Resistor
-  digitalWrite(EC_PIN_RELAY_PROBE,LOW);
+  ec_releaseRelay();
-  digitalWrite(EC_PIN_RELAY_CALIBRATION,LOW);
+
-  digitalWrite(EC_PIN_RELAY_RANGE,LOW);
 }
 
-void ec_loop(unsigned long loopmillis, unsigned long pInterval) {
+void ec_loop(unsigned long loopmillis) {
-  if (loopmillis>last_read_ec+pInterval) {
+  static unsigned long last_measurement_ec=0;
-    last_read_ec=loopmillis;
+  static unsigned long last_read_ec=0;
-    ec_array_pos++;
-    flag_print= ec_array_pos==EC_ARRAY_SIZE;
-    ec_array_pos%=EC_ARRAY_SIZE;
-    ec_array[ec_array_pos]=analogRead(EC_PIN_ADC);
 
-    //Serial.print(ec_array[ec_array_pos]); Serial.print(" ");
+  switch (ecstate) {
+    case IDLE:
+      
+      if (loopmillis>last_measurement_ec+EC_MEASUREMENT_INTERVAL && ecstate==IDLE) { //start measurement if idle
+        last_measurement_ec=loopmillis;
+        ec_startMeasurement();
+        ec_connectProbe(true);
+        ecstate=MEASURE;
+        Serial.println("EC Take Measurement");
+      }
+      break;
+
+    case MEASURE:
+      if (ec_measurementReady()) {
+        ec_releaseRelay();
+        float adc_rangelow=getMean(ec_array_rangeLow,EC_ARRAY_SIZE);
+        float adc_rangehigh=getMean(ec_array_rangeHigh,EC_ARRAY_SIZE);
+
+        Serial.print("EC ADC: Low="); Serial.print(adc_rangelow); Serial.print(" High="); Serial.println(adc_rangehigh);
+
+        ecstate=IDLE;
+      }
+      
+      break;
+
+  }
+
+
+
+  if (loopmillis>last_read_ec+EC_READ_INTERVAL && ec_array_pos/2<EC_ARRAY_SIZE) { //take reading into array if measurement running
+    last_read_ec=loopmillis;
+
+    //flag_print= ec_array_pos==EC_ARRAY_SIZE;
+    //ec_array_pos%=EC_ARRAY_SIZE;
+
+    if (ec_array_pos<EC_ARRAY_SIZE){ //low range
+      ec_setRange(LOW);
+    }else{ //high range
+      ec_setRange(HIGH);
+    }
+
+    if (loopmillis>ec_last_change_relay+EC_RELAY_SWITCH_SETTLETIME) { //values have settled
+      uint16_t value=analogRead(EC_PIN_ADC);
+      if (ec_array_pos<EC_ARRAY_SIZE){ //low range
+        ec_array_rangeLow[ec_array_pos%EC_ARRAY_SIZE]=value;
+        
+      }else{ //high range
+        ec_array_rangeHigh[ec_array_pos%EC_ARRAY_SIZE]=value;
+        
+      }
+
+      
+      /*
+      if (ec_array_pos==0) {
+        Serial.println(""); Serial.print("Lowrange:");
+      }
+      if (ec_array_pos==EC_ARRAY_SIZE) {
+        Serial.println(""); Serial.print("Highrange:");
+      }
+      Serial.print(value); Serial.print(" ");
+      if (ec_array_pos==EC_ARRAY_SIZE*2-1) {
+        Serial.println("");
+      }
+      */
+      
+      
+      ec_array_pos++;
+    }
+    
+  }  
+  
+}
+
+
+
+void ec_startMeasurement() {
+  ec_array_pos=0;
+}
+
+bool ec_measurementReady(){
+  if (ec_array_pos>=EC_ARRAY_SIZE*2) { //reached end of both arrays
+    return true;
+  }else{
+    return false;
   }
 }
 
+void ec_setRange(bool range) {
+  //range low means low resistor value -> NO -> relay High
+  bool val=digitalRead(EC_PIN_RELAY_RANGE);
+  if (val!=!range) { //write only if different
+    digitalWrite(EC_PIN_RELAY_RANGE,!range);
+    ec_last_change_relay=millis();
+  }
+}
+
+void ec_connectProbe(bool relay) {
+  bool val=digitalRead(EC_PIN_RELAY_PROBE);
+  if (val!=relay) { //write only if different
+    digitalWrite(EC_PIN_RELAY_PROBE,relay);
+    ec_last_change_relay=millis();
+  }
+}
+
+void ec_releaseRelay() {
+  digitalWrite(EC_PIN_RELAY_PROBE,LOW);
+  digitalWrite(EC_PIN_RELAY_RANGE,LOW);
+  ec_last_change_relay=millis();
+}
+
+
 #endif

include/flow.h

@@ -19,8 +19,8 @@ void flow_setup() {
     attachInterrupt(FLOW_PIN, isr_flow, CHANGE);
 }
 
-void flow_loop(unsigned long loopmillis, unsigned long pInterval) {
+void flow_loop(unsigned long loopmillis) {
-     if (loopmillis>=last_read_flow+pInterval) {
+     if (loopmillis>=last_read_flow+READINTERVAL_FLOW) {
     flow=flow_counter*1000.0/(loopmillis-last_read_flow)/2.0; //Frequency [Hz]
     flow/=flow_factor; //[L/min]
   

include/temperature.h

@@ -78,12 +78,12 @@ void temperature_setup() {
 }
 
 
-void temperature_loop(unsigned long loopmillis, unsigned long pInterval) {
+void temperature_loop(unsigned long loopmillis) {
 
   static unsigned long last_read_ds18b20;
   static bool flag_requestTemperatures=false;
-  if (loopmillis>last_read_ds18b20+pInterval) { 
+  if (loopmillis>last_read_ds18b20+READINTERVAL_DS18B20) { 
-    if (loopmillis>last_read_ds18b20+pInterval*10) { //timeout
+    if (loopmillis>last_read_ds18b20+READINTERVAL_DS18B20*10) { //timeout
       Serial.println("Warn: Request Temperatures Timeout!");
       flag_requestTemperatures=false;
     }

include/waterlevel.h

@@ -24,10 +24,10 @@ void waterlevel_setup() {
   }
 }
 
-void waterlevel_loop(unsigned long loopmillis, unsigned long pInterval) {
+void waterlevel_loop(unsigned long loopmillis) {
 
   static unsigned long last_read_hcsr04;
-  if (loopmillis>=last_read_hcsr04+pInterval) {
+  if (loopmillis>=last_read_hcsr04+READINTERVAL_HCSR04) {
     last_read_hcsr04=loopmillis;
     float temperature=20.0;
     if (tempC_air!=DEVICE_DISCONNECTED_C && isValueArrayOKf(tempCmean_air,TEMPMEAN_SIZE,DEVICE_DISCONNECTED_C)) { //sensor ok

src/main.cpp

@@ -51,22 +51,24 @@ void loop() {
   flag_print=false;
 
   
-  ec_loop(loopmillis, EC_READ_INTERVAL);
+  ec_loop(loopmillis);
   
 
-  temperature_loop(loopmillis, READINTERVAL_DS18B20);
+  temperature_loop(loopmillis);
 
   
-  waterlevel_loop(loopmillis, READINTERVAL_HCSR04);
+  waterlevel_loop(loopmillis);
 
 
-  flow_loop(loopmillis, READINTERVAL_FLOW);
+  flow_loop(loopmillis);
  
 
   
   if (loopmillis>last_print+500) { 
     last_print=loopmillis;
 
+
+    /*
     if (isValueArrayOK(ec_array,EC_ARRAY_SIZE,0))
     {
       Serial.print("EC=");
@@ -75,6 +77,7 @@ void loop() {
     }else{
       Serial.print("Waiting for EC");
     }
+    
 
     if (isValueArrayOKf(tempCmean_reservoir,TEMPMEAN_SIZE,DEVICE_DISCONNECTED_C)){
       Serial.print("\t Treservoir="); Serial.print(getMeanf(tempCmean_reservoir,TEMPMEAN_SIZE)); Serial.print("\t Tair="); Serial.print(getMeanf(tempCmean_air,TEMPMEAN_SIZE));
@@ -103,6 +106,7 @@ void loop() {
     
 
     Serial.println();   
+    */
     
   }