interfisch
/
rf24-pio
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
rf24-pio/RF24.cpp

970 lines
24 KiB
C++
Raw Blame History

/*
Copyright (C) 2011 James Coliz, Jr. <maniacbug@ymail.com>
This program is free software; you can redistribute it and/or
modify it under the terms of the GNU General Public License
version 2 as published by the Free Software Foundation.
*/
#include <WProgram.h>
#include <SPI.h>
#include "nRF24L01.h"
#include "RF24.h"
#undef SERIAL_DEBUG
#ifdef SERIAL_DEBUG
#define IF_SERIAL_DEBUG(x) ({x;})
#else
#define IF_SERIAL_DEBUG(x)
#endif
// Avoid spurious warnings
#ifndef NATIVE
#undef PROGMEM
#define PROGMEM __attribute__(( section(".progmem.data") ))
#undef PSTR
#define PSTR(s) (__extension__({static prog_char __c[] PROGMEM = (s); &__c[0];}))
#endif
/****************************************************************************/
void RF24::csn(int mode)
{
// Minimum ideal SPI bus speed is 2x data rate
// If we assume 2Mbs data rate and 16Mhz clock, a
// divider of 4 is the minimum we want.
// CLK:BUS 8Mhz:2Mhz, 16Mhz:4Mhz, or 20Mhz:5Mhz
SPI.setBitOrder(MSBFIRST);
SPI.setDataMode(SPI_MODE0);
SPI.setClockDivider(SPI_CLOCK_DIV4);
digitalWrite(csn_pin,mode);
}
/****************************************************************************/
void RF24::ce(int level)
{
digitalWrite(ce_pin,level);
}
/****************************************************************************/
uint8_t RF24::read_register(uint8_t reg, uint8_t* buf, uint8_t len)
{
uint8_t status;
csn(LOW);
status = SPI.transfer( R_REGISTER | ( REGISTER_MASK & reg ) );
while ( len-- )
*buf++ = SPI.transfer(0xff);
csn(HIGH);
return status;
}
/****************************************************************************/
uint8_t RF24::read_register(uint8_t reg)
{
csn(LOW);
SPI.transfer( R_REGISTER | ( REGISTER_MASK & reg ) );
uint8_t result = SPI.transfer(0xff);
csn(HIGH);
return result;
}
/****************************************************************************/
uint8_t RF24::write_register(uint8_t reg, const uint8_t* buf, uint8_t len)
{
uint8_t status;
csn(LOW);
status = SPI.transfer( W_REGISTER | ( REGISTER_MASK & reg ) );
while ( len-- )
SPI.transfer(*buf++);
csn(HIGH);
return status;
}
/****************************************************************************/
uint8_t RF24::write_register(uint8_t reg, uint8_t value)
{
uint8_t status;
IF_SERIAL_DEBUG(printf_P(PSTR("write_register(%02x,%02x)\n\r"),reg,value));
csn(LOW);
status = SPI.transfer( W_REGISTER | ( REGISTER_MASK & reg ) );
SPI.transfer(value);
csn(HIGH);
return status;
}
/****************************************************************************/
uint8_t RF24::write_payload(const void* buf, uint8_t len)
{
uint8_t status;
const uint8_t* current = reinterpret_cast<const uint8_t*>(buf);
uint8_t data_len = min(len,payload_size);
uint8_t blank_len = dynamic_payloads_enabled ? 0 : payload_size - data_len;
//printf("[Writing %u bytes %u blanks]",data_len,blank_len);
csn(LOW);
status = SPI.transfer( W_TX_PAYLOAD );
while ( data_len-- )
SPI.transfer(*current++);
while ( blank_len-- )
SPI.transfer(0);
csn(HIGH);
return status;
}
/****************************************************************************/
uint8_t RF24::read_payload(void* buf, uint8_t len)
{
uint8_t status;
uint8_t* current = reinterpret_cast<uint8_t*>(buf);
uint8_t data_len = min(len,payload_size);
uint8_t blank_len = dynamic_payloads_enabled ? 0 : payload_size - data_len;
//printf("[Reading %u bytes %u blanks]",data_len,blank_len);
csn(LOW);
status = SPI.transfer( R_RX_PAYLOAD );
while ( data_len-- )
*current++ = SPI.transfer(0xff);
while ( blank_len-- )
SPI.transfer(0xff);
csn(HIGH);
return status;
}
/****************************************************************************/
uint8_t RF24::flush_rx(void)
{
uint8_t status;
csn(LOW);
status = SPI.transfer( FLUSH_RX );
csn(HIGH);
return status;
}
/****************************************************************************/
uint8_t RF24::flush_tx(void)
{
uint8_t status;
csn(LOW);
status = SPI.transfer( FLUSH_TX );
csn(HIGH);
return status;
}
/****************************************************************************/
uint8_t RF24::get_status(void)
{
uint8_t status;
csn(LOW);
status = SPI.transfer( NOP );
csn(HIGH);
return status;
}
/****************************************************************************/
void RF24::print_status(uint8_t status)
{
printf_P(PSTR("STATUS\t\t = 0x%02x RX_DR=%x TX_DS=%x MAX_RT=%x RX_P_NO=%x TX_FULL=%x\n\r"),
status,
(status & _BV(RX_DR))?1:0,
(status & _BV(TX_DS))?1:0,
(status & _BV(MAX_RT))?1:0,
((status >> RX_P_NO) & B111),
(status & _BV(TX_FULL))?1:0
);
}
/****************************************************************************/
void RF24::print_observe_tx(uint8_t value)
{
printf_P(PSTR("OBSERVE_TX=%02x: POLS_CNT=%x ARC_CNT=%x\n\r"),
value,
(value >> PLOS_CNT) & B1111,
(value >> ARC_CNT) & B1111
);
}
/****************************************************************************/
void RF24::print_byte_register(prog_char* name, uint8_t reg, uint8_t qty)
{
char extra_tab = strlen_P(name) < 8 ? '\t' : 0;
printf_P(PSTR("%S\t%c ="),name,extra_tab);
while (qty--)
printf_P(PSTR(" 0x%02x"),read_register(reg++));
printf_P(PSTR("\n\r"));
}
/****************************************************************************/
void RF24::print_address_register(prog_char* name, uint8_t reg, uint8_t qty)
{
char extra_tab = strlen_P(name) < 8 ? '\t' : 0;
printf_P(PSTR("%S\t%c ="),name,extra_tab);
while (qty--)
{
uint8_t buffer[5];
read_register(reg++,buffer,sizeof buffer);
printf_P(PSTR(" 0x"));
uint8_t* bufptr = buffer + sizeof buffer;
while( --bufptr >= buffer )
printf_P(PSTR("%02x"),*bufptr);
}
printf_P(PSTR("\n\r"));
}
/****************************************************************************/
RF24::RF24(uint8_t _cepin, uint8_t _cspin):
ce_pin(_cepin), csn_pin(_cspin), wide_band(true), p_variant(false),
payload_size(32), ack_payload_available(false), dynamic_payloads_enabled(false),
pipe0_reading_address(0)
{
}
/****************************************************************************/
void RF24::setChannel(uint8_t channel)
{
// TODO: This method could take advantage of the 'wide_band' calculation
// done in setChannel() to require certain channel spacing.
write_register(RF_CH,min(channel,127));
}
/****************************************************************************/
void RF24::setPayloadSize(uint8_t size)
{
payload_size = min(size,32);
}
/****************************************************************************/
uint8_t RF24::getPayloadSize(void)
{
return payload_size;
}
/****************************************************************************/
void RF24::printDetails(void)
{
print_status(get_status());
print_address_register(PSTR("RX_ADDR_P0-1"),RX_ADDR_P0,2);
print_byte_register(PSTR("RX_ADDR_P2-5"),RX_ADDR_P2,4);
print_address_register(PSTR("TX_ADDR"),TX_ADDR);
print_byte_register(PSTR("RX_PW_P0-6"),RX_PW_P0,6);
print_byte_register(PSTR("EN_AA"),EN_AA);
print_byte_register(PSTR("EN_RXADDR"),EN_RXADDR);
print_byte_register(PSTR("RF_CH"),RF_CH);
print_byte_register(PSTR("RF_SETUP"),RF_SETUP);
print_byte_register(PSTR("CONFIG"),CONFIG);
print_byte_register(PSTR("DYNPD/FEATURE"),DYNPD,2);
const char * rf24_datarate_e_str[] = { "1MBPS", "2MBPS", "250KBPS" };
const char * rf24_model_e_str[] = { "nRF24L01", "nRF24L01+" } ;
const char * rf24_crclength_e_str[] = { "Disabled", "8 bits", "16 bits" } ;
const char * rf24_pa_dbm_e_str[] = { "PA_MIN", "PA_LOW", "LA_MED", "PA_HIGH"} ;
printf_P(PSTR("Data Rate\t = %s\n\r"),rf24_datarate_e_str[getDataRate()]);
printf_P(PSTR("Model\t\t = %s\n\r"),rf24_model_e_str[isPVariant()]);
printf_P(PSTR("CRC Length\t = %s\n\r"),rf24_crclength_e_str[getCRCLength()]);
printf_P(PSTR("PA Power\t = %s\n\r"),rf24_pa_dbm_e_str[getPALevel()]);
}
/****************************************************************************/
void RF24::begin(void)
{
// Initialize pins
pinMode(ce_pin,OUTPUT);
pinMode(csn_pin,OUTPUT);
// Initialize SPI bus
SPI.begin();
ce(LOW);
csn(HIGH);
// Must allow the radio time to settle else configuration bits will not necessarily stick.
// This is actually only required following power up but some settling time also appears to
// be required after resets too. For full coverage, we'll always assume the worst.
// Enabling 16b CRC is by far the most obvious case if the wrong timing is used - or skipped.
// Technically we require 4.5ms + 14us as a worst case. We'll just call it 5ms for good measure.
// WARNING: Delay is based on P-variant whereby non-P *may* require different timing.
delay( 5 ) ;
// Set 1500uS (minimum for 32B payload in ESB@250KBPS) timeouts, to make testing a little easier
// WARNING: If this is ever lowered, either 250KBS mode with AA is broken or maximum packet
// sizes must never be used. See documentation for a more complete explanation.
write_register(SETUP_RETR,(B0100 << ARD) | (B1111 << ARC));
// Restore our default PA level
setPALevel( RF24_PA_MAX ) ;
// Determine if this is a p or non-p RF24 module and then
// reset our data rate back to default value. This works
// because a non-P variant won't allow the data rate to
// be set to 250Kbps.
if( setDataRate( RF24_250KBPS ) )
{
p_variant = true ;
}
// Then set the data rate to the slowest (and most reliable) speed supported by all
// hardware.
setDataRate( RF24_1MBPS ) ;
// Initialize CRC and request 2-byte (16bit) CRC
setCRCLength( RF24_CRC_16 ) ;
// Disable dynamic payloads, to match dynamic_payloads_enabled setting
write_register(DYNPD,0);
// Reset current status
// Notice reset and flush is the last thing we do
write_register(STATUS,_BV(RX_DR) | _BV(TX_DS) | _BV(MAX_RT) );
// Set up default configuration. Callers can always change it later.
// This channel should be universally safe and not bleed over into adjacent
// spectrum.
setChannel(76);
// Flush buffers
flush_rx();
flush_tx();
}
/****************************************************************************/
void RF24::startListening(void)
{
write_register(CONFIG, read_register(CONFIG) | _BV(PWR_UP) | _BV(PRIM_RX));
write_register(STATUS, _BV(RX_DR) | _BV(TX_DS) | _BV(MAX_RT) );
// Restore the pipe0 adddress, if exists
if (pipe0_reading_address)
write_register(RX_ADDR_P0, reinterpret_cast<const uint8_t*>(&pipe0_reading_address), 5);
// Flush buffers
flush_rx();
// Go!
ce(HIGH);
// wait for the radio to come up (130us actually only needed)
delayMicroseconds(130);
}
/****************************************************************************/
void RF24::stopListening(void)
{
ce(LOW);
}
/****************************************************************************/
void RF24::powerDown(void)
{
write_register(CONFIG,read_register(CONFIG) & ~_BV(PWR_UP));
}
/****************************************************************************/
void RF24::powerUp(void)
{
write_register(CONFIG,read_register(CONFIG) | _BV(PWR_UP));
}
/******************************************************************/
bool RF24::write( const void* buf, uint8_t len )
{
bool result = false;
// Begin the write
startWrite(buf,len);
// ------------
// At this point we could return from a non-blocking write, and then call
// the rest after an interrupt
// Instead, we are going to block here until we get TX_DS (transmission completed and ack'd)
// or MAX_RT (maximum retries, transmission failed). Also, we'll timeout in case the radio
// is flaky and we get neither.
// IN the end, the send should be blocking. It comes back in 60ms worst case, or much faster
// if I tighted up the retry logic. (Default settings will be 1500us.
// Monitor the send
uint8_t observe_tx;
uint8_t status;
uint32_t sent_at = millis();
const uint32_t timeout = 500; //ms to wait for timeout
do
{
status = read_register(OBSERVE_TX,&observe_tx,1);
IF_SERIAL_DEBUG(Serial.print(observe_tx,HEX));
}
while( ! ( status & ( _BV(TX_DS) | _BV(MAX_RT) ) ) && ( millis() - sent_at < timeout ) );
// The part above is what you could recreate with your own interrupt handler,
// and then call this when you got an interrupt
// ------------
// Call this when you get an interrupt
// The status tells us three things
// * The send was successful (TX_DS)
// * The send failed, too many retries (MAX_RT)
// * There is an ack packet waiting (RX_DR)
bool tx_ok, tx_fail;
whatHappened(tx_ok,tx_fail,ack_payload_available);
//printf("%u%u%u\n\r",tx_ok,tx_fail,ack_payload_available);
result = tx_ok;
IF_SERIAL_DEBUG(Serial.print(result?"...OK.":"...Failed"));
// Handle the ack packet
if ( ack_payload_available )
{
ack_payload_length = getDynamicPayloadSize();
IF_SERIAL_DEBUG(Serial.print("[AckPacket]/"));
IF_SERIAL_DEBUG(Serial.println(ack_payload_length,DEC));
}
// Yay, we are done.
// Power down
powerDown();
// Flush buffers (Is this a relic of past experimentation, and not needed anymore??)
flush_tx();
return result;
}
/****************************************************************************/
void RF24::startWrite( const void* buf, uint8_t len )
{
// Transmitter power-up
write_register(CONFIG, ( read_register(CONFIG) | _BV(PWR_UP) ) & ~_BV(PRIM_RX) );
delay(2);
// Send the payload
write_payload( buf, len );
// Allons!
ce(HIGH);
delayMicroseconds(15);
delay(2);
ce(LOW);
}
/****************************************************************************/
uint8_t RF24::getDynamicPayloadSize(void)
{
uint8_t result = 0;
csn(LOW);
SPI.transfer( R_RX_PL_WID );
result = SPI.transfer(0xff);
csn(HIGH);
return result;
}
/****************************************************************************/
bool RF24::available(void)
{
return available(NULL);
}
/****************************************************************************/
bool RF24::available(uint8_t* pipe_num)
{
uint8_t status = get_status();
// Too noisy, enable if you really want lots o data!!
//IF_SERIAL_DEBUG(print_status(status));
bool result = ( status & _BV(RX_DR) );
if (result)
{
// If the caller wants the pipe number, include that
if ( pipe_num )
*pipe_num = ( status >> RX_P_NO ) & B111;
// Clear the status bit
// ??? Should this REALLY be cleared now? Or wait until we
// actually READ the payload?
write_register(STATUS,_BV(RX_DR) );
// Handle ack payload receipt
if ( status & _BV(TX_DS) )
{
write_register(STATUS,_BV(TX_DS));
}
}
return result;
}
/****************************************************************************/
bool RF24::read( void* buf, uint8_t len )
{
// Fetch the payload
read_payload( buf, len );
// was this the last of the data available?
return read_register(FIFO_STATUS) & _BV(RX_EMPTY);
}
/****************************************************************************/
void RF24::whatHappened(bool& tx_ok,bool& tx_fail,bool& rx_ready)
{
// Read the status & reset the status in one easy call
// Or is that such a good idea?
uint8_t status = write_register(STATUS,_BV(RX_DR) | _BV(TX_DS) | _BV(MAX_RT) );
// Report to the user what happened
tx_ok = status & _BV(TX_DS);
tx_fail = status & _BV(MAX_RT);
rx_ready = status & _BV(RX_DR);
}
/****************************************************************************/
void RF24::openWritingPipe(uint64_t value)
{
// Note that AVR 8-bit uC's store this LSB first, and the NRF24L01(+)
// expects it LSB first too, so we're good.
write_register(RX_ADDR_P0, reinterpret_cast<uint8_t*>(&value), 5);
write_register(TX_ADDR, reinterpret_cast<uint8_t*>(&value), 5);
write_register(RX_PW_P0,min(payload_size,32));
}
/****************************************************************************/
void RF24::openReadingPipe(uint8_t child, uint64_t address)
{
const uint8_t child_pipe[] =
{
RX_ADDR_P0, RX_ADDR_P1, RX_ADDR_P2, RX_ADDR_P3, RX_ADDR_P4, RX_ADDR_P5
};
const uint8_t child_payload_size[] =
{
RX_PW_P0, RX_PW_P1, RX_PW_P2, RX_PW_P3, RX_PW_P4, RX_PW_P5
};
const uint8_t child_pipe_enable[] =
{
ERX_P0, ERX_P1, ERX_P2, ERX_P3, ERX_P4, ERX_P5
};
// If this is pipe 0, cache the address. This is needed because
// openWritingPipe() will overwrite the pipe 0 address, so
// startListening() will have to restore it.
if (child == 0)
pipe0_reading_address = address;
if (child <= 6)
{
// For pipes 2-5, only write the LSB
if ( child < 2 )
write_register(child_pipe[child], reinterpret_cast<const uint8_t*>(&address), 5);
else
write_register(child_pipe[child], reinterpret_cast<const uint8_t*>(&address), 1);
write_register(child_payload_size[child],payload_size);
// Note it would be more efficient to set all of the bits for all open
// pipes at once. However, I thought it would make the calling code
// more simple to do it this way.
write_register(EN_RXADDR,read_register(EN_RXADDR) | _BV(child_pipe_enable[child]));
}
}
/****************************************************************************/
void RF24::toggle_features(void)
{
csn(LOW);
SPI.transfer( ACTIVATE );
SPI.transfer( 0x73 );
csn(HIGH);
}
/****************************************************************************/
void RF24::enableDynamicPayloads(void)
{
// Enable dynamic payload throughout the system
write_register(FEATURE,read_register(FEATURE) | _BV(EN_DPL) );
// If it didn't work, the features are not enabled
if ( ! read_register(FEATURE) )
{
// So enable them and try again
toggle_features();
write_register(FEATURE,read_register(FEATURE) | _BV(EN_DPL) );
}
IF_SERIAL_DEBUG(printf("FEATURE=%i\n\r",read_register(FEATURE)));
// Enable dynamic payload on all pipes
//
// Not sure the use case of only having dynamic payload on certain
// pipes, so the library does not support it.
write_register(DYNPD,read_register(DYNPD) | _BV(DPL_P5) | _BV(DPL_P4) | _BV(DPL_P3) | _BV(DPL_P2) | _BV(DPL_P1) | _BV(DPL_P0));
dynamic_payloads_enabled = true;
}
/****************************************************************************/
void RF24::enableAckPayload(void)
{
//
// enable ack payload and dynamic payload features
//
write_register(FEATURE,read_register(FEATURE) | _BV(EN_ACK_PAY) | _BV(EN_DPL) );
// If it didn't work, the features are not enabled
if ( ! read_register(FEATURE) )
{
// So enable them and try again
toggle_features();
write_register(FEATURE,read_register(FEATURE) | _BV(EN_ACK_PAY) | _BV(EN_DPL) );
}
IF_SERIAL_DEBUG(printf("FEATURE=%i\n\r",read_register(FEATURE)));
//
// Enable dynamic payload on pipes 0 & 1
//
write_register(DYNPD,read_register(DYNPD) | _BV(DPL_P1) | _BV(DPL_P0));
}
/****************************************************************************/
void RF24::writeAckPayload(uint8_t pipe, const void* buf, uint8_t len)
{
const uint8_t* current = reinterpret_cast<const uint8_t*>(buf);
csn(LOW);
SPI.transfer( W_ACK_PAYLOAD | ( pipe & B111 ) );
uint8_t data_len = min(len,32);
while ( data_len-- )
SPI.transfer(*current++);
csn(HIGH);
}
/****************************************************************************/
bool RF24::isAckPayloadAvailable(void)
{
bool result = ack_payload_available;
ack_payload_available = false;
return result;
}
/****************************************************************************/
bool RF24::isPVariant(void)
{
return p_variant ;
}
/****************************************************************************/
void RF24::setAutoAck(bool enable)
{
if ( enable )
write_register(EN_AA, B111111);
else
write_register(EN_AA, 0);
}
/****************************************************************************/
void RF24::setAutoAck( uint8_t pipe, bool enable )
{
if ( pipe <= 6 )
{
uint8_t en_aa = read_register( EN_AA ) ;
if( enable )
{
en_aa |= _BV(pipe) ;
}
else
{
en_aa &= ~_BV(pipe) ;
}
write_register( EN_AA, en_aa ) ;
}
}
/****************************************************************************/
bool RF24::testCarrier(void)
{
return ( read_register(CD) & 1 );
}
/****************************************************************************/
bool RF24::testRPD(void)
{
return ( read_register(RPD) & 1 ) ;
}
/****************************************************************************/
void RF24::setPALevel(rf24_pa_dbm_e level)
{
uint8_t setup = read_register(RF_SETUP) ;
setup &= ~(_BV(RF_PWR_LOW) | _BV(RF_PWR_HIGH)) ;
switch( level )
{
case RF24_PA_MAX:
setup |= (_BV(RF_PWR_LOW) | _BV(RF_PWR_HIGH)) ;
break ;
case RF24_PA_HIGH:
setup |= _BV(RF_PWR_HIGH) ;
break ;
case RF24_PA_LOW:
setup |= _BV(RF_PWR_LOW) ;
break ;
case RF24_PA_MIN:
break ;
case RF24_PA_ERROR:
// On error, go to maximum PA
setup |= (_BV(RF_PWR_LOW) | _BV(RF_PWR_HIGH)) ;
break ;
}
write_register( RF_SETUP, setup ) ;
}
/****************************************************************************/
rf24_pa_dbm_e RF24::getPALevel(void)
{
rf24_pa_dbm_e result = RF24_PA_ERROR ;
uint8_t power = read_register(RF_SETUP) & (_BV(RF_PWR_LOW) | _BV(RF_PWR_HIGH)) ;
switch( power )
{
case (_BV(RF_PWR_LOW) | _BV(RF_PWR_HIGH)):
result = RF24_PA_MAX ;
break ;
case _BV(RF_PWR_HIGH):
result = RF24_PA_HIGH ;
break ;
case _BV(RF_PWR_LOW):
result = RF24_PA_LOW ;
break ;
default:
result = RF24_PA_MIN ;
break ;
}
return result ;
}
/****************************************************************************/
bool RF24::setDataRate(rf24_datarate_e speed)
{
bool result = false;
uint8_t setup = read_register(RF_SETUP) ;
// HIGH and LOW '00' is 1Mbs - our default
wide_band = false ;
setup &= ~(_BV(RF_DR_LOW) | _BV(RF_DR_HIGH)) ;
if( speed == RF24_250KBPS )
{
// Must set the RF_DR_LOW to 1; RF_DR_HIGH (used to be RF_DR) is already 0
// Making it '10'.
wide_band = false ;
setup |= _BV( RF_DR_LOW ) ;
}
else
{
// Set 2Mbs, RF_DR (RF_DR_HIGH) is set 1
// Making it '01'
if ( speed == RF24_2MBPS )
{
wide_band = true ;
setup |= _BV(RF_DR_HIGH);
}
else
{
// 1Mbs
wide_band = false ;
}
}
write_register(RF_SETUP,setup);
// Verify our result
if ( read_register(RF_SETUP) == setup )
{
result = true;
}
else
{
wide_band = false;
}
return result;
}
/****************************************************************************/
rf24_datarate_e RF24::getDataRate( void )
{
rf24_datarate_e result ;
uint8_t setup = read_register(RF_SETUP) ;
// Order matters in our case below
switch( setup & (_BV(RF_DR_LOW) | _BV(RF_DR_HIGH)) )
{
case _BV(RF_DR_LOW):
// '10' = 250KBPS
result = RF24_250KBPS ;
break ;
case _BV(RF_DR_HIGH):
// '01' = 2MBPS
result = RF24_2MBPS ;
break ;
default:
// '00' = 1MBPS
result = RF24_1MBPS ;
break ;
}
return result ;
}
/****************************************************************************/
void RF24::setCRCLength(rf24_crclength_e length)
{
uint8_t config = read_register(CONFIG) & ~( _BV(CRCO) | _BV(EN_CRC)) ;
switch (length)
{
case RF24_CRC_DISABLED:
break;
case RF24_CRC_8:
config |= _BV(EN_CRC);
break;
case RF24_CRC_16:
default:
config |= _BV(EN_CRC);
config |= _BV( CRCO );
break;
}
write_register( CONFIG, config ) ;
}
/****************************************************************************/
rf24_crclength_e RF24::getCRCLength(void)
{
rf24_crclength_e result = RF24_CRC_DISABLED;
uint8_t config = read_register(CONFIG) & ( _BV(CRCO) | _BV(EN_CRC)) ;
if ( config & _BV(EN_CRC ) )
{
if ( config & _BV(CRCO) )
result = RF24_CRC_16;
else
result = RF24_CRC_8;
}
return result;
}
/****************************************************************************/
void RF24::disableCRC( void )
{
uint8_t disable = read_register(CONFIG) & ~_BV(EN_CRC) ;
write_register( CONFIG, disable ) ;
}
/****************************************************************************/
void RF24::setRetries(uint8_t delay, uint8_t count)
{
write_register(SETUP_RETR,(delay&0xf)<<ARD | (count&0xf)<<ARC);
}
// vim:ai:cin:sts=2 sw=2 ft=cpp
Reference in New Issue View Git Blame Copy Permalink