move sensors to separate files
This commit is contained in:
parent
c63b4d01f0
commit
576860ae31
|
|
@ -0,0 +1,41 @@
|
|||
#ifndef _EC_H_
|
||||
#define _EC_H_
|
||||
|
||||
#include <Arduino.h>
|
||||
|
||||
|
||||
|
||||
#define EC_PIN_ADC 4
|
||||
#define EC_PIN_FREQ 5
|
||||
#define EC_PWM_CH 0
|
||||
#define EC_RESOLUTION 8
|
||||
#define EC_FREQUENCY 5000
|
||||
|
||||
#define EC_ARRAY_SIZE 1024
|
||||
uint16_t ec_array[EC_ARRAY_SIZE];
|
||||
uint16_t ec_array_pos=0;
|
||||
unsigned long last_read_ec=0;
|
||||
#define EC_READ_INTERVAL 1
|
||||
|
||||
void ec_setup() {
|
||||
pinMode(EC_PIN_ADC,INPUT);
|
||||
|
||||
ledcSetup(EC_PWM_CH, EC_FREQUENCY, EC_RESOLUTION);
|
||||
ledcAttachPin(EC_PIN_FREQ, EC_PWM_CH);
|
||||
ledcWrite(EC_PWM_CH, 127);
|
||||
|
||||
}
|
||||
|
||||
void ec_loop(unsigned long loopmillis, unsigned long pInterval) {
|
||||
if (loopmillis>last_read_ec+pInterval) {
|
||||
last_read_ec=loopmillis;
|
||||
ec_array_pos++;
|
||||
flag_print= ec_array_pos==EC_ARRAY_SIZE;
|
||||
ec_array_pos%=EC_ARRAY_SIZE;
|
||||
ec_array[ec_array_pos]=analogRead(EC_PIN_ADC);
|
||||
|
||||
//Serial.print(ec_array[ec_array_pos]); Serial.print(" ");
|
||||
}
|
||||
}
|
||||
|
||||
#endif
|
||||
|
|
@ -0,0 +1,38 @@
|
|||
#ifndef _FLOW_H_
|
||||
#define _FLOW_H_
|
||||
|
||||
#define FLOW_PIN 19
|
||||
uint16_t flow_counter=0; //maximum counts/s measured with Eden 128 Pump was 171
|
||||
void IRAM_ATTR isr_flow();
|
||||
unsigned long last_read_flow=0;
|
||||
#define READINTERVAL_FLOW 1000
|
||||
float flow_factor=7.5; //F=7.5*flowrate[L/min]
|
||||
float flow;
|
||||
|
||||
uint32_t flow_counter_sum=0;
|
||||
|
||||
|
||||
|
||||
void flow_setup() {
|
||||
|
||||
pinMode(FLOW_PIN, INPUT_PULLUP);
|
||||
attachInterrupt(FLOW_PIN, isr_flow, CHANGE);
|
||||
}
|
||||
|
||||
void flow_loop(unsigned long loopmillis, unsigned long pInterval) {
|
||||
if (loopmillis>=last_read_flow+pInterval) {
|
||||
flow=flow_counter*1000.0/(loopmillis-last_read_flow)/2.0; //Frequency [Hz]
|
||||
flow/=flow_factor; //[L/min]
|
||||
|
||||
flow_counter=0;
|
||||
last_read_flow=loopmillis;
|
||||
}
|
||||
}
|
||||
|
||||
void IRAM_ATTR isr_flow() {
|
||||
flow_counter++;
|
||||
flow_counter_sum++;
|
||||
}
|
||||
|
||||
|
||||
#endif
|
||||
|
|
@ -0,0 +1,117 @@
|
|||
#ifndef _HELPFUNCTIONS_H_
|
||||
#define _HELPFUNCTIONS_H_
|
||||
|
||||
#include <Arduino.h>
|
||||
#include <ArduinoSort.h>
|
||||
|
||||
float getMean(uint16_t *parray,uint16_t psize);
|
||||
float getMeanf(float *parray,uint16_t psize);
|
||||
uint16_t getMin(uint16_t *parray, uint16_t psize);
|
||||
uint16_t getMax(uint16_t *parray, uint16_t psize);
|
||||
float getMaxf(float *parray,uint16_t psize);
|
||||
float getMinf(float *parray, uint16_t psize);
|
||||
bool isValueArrayOK(uint16_t *parray,uint16_t psize, uint16_t pcheck);
|
||||
bool isValueArrayOKf(float *parray,uint16_t psize, float pcheck);
|
||||
float getFilteredf(float *parray,uint16_t psize, uint16_t pcutOff);
|
||||
|
||||
|
||||
float getMean(uint16_t *parray,uint16_t psize) {
|
||||
double mean=0;
|
||||
for (uint16_t i=0;i<psize;i++) {
|
||||
mean+=parray[i];
|
||||
}
|
||||
|
||||
return mean/psize;
|
||||
}
|
||||
float getMeanf(float *parray,uint16_t psize) {
|
||||
double mean=0;
|
||||
for (uint16_t i=0;i<psize;i++) {
|
||||
mean+=parray[i];
|
||||
}
|
||||
|
||||
return mean/psize;
|
||||
}
|
||||
|
||||
bool isValueArrayOK(uint16_t *parray,uint16_t psize, uint16_t pcheck) { //check if array has error values
|
||||
for (uint16_t i=0;i<psize;i++) {
|
||||
if (parray[i]==pcheck){
|
||||
return false;
|
||||
}
|
||||
}
|
||||
return true;
|
||||
}
|
||||
bool isValueArrayOKf(float *parray,uint16_t psize, float pcheck) { //check if array has error values
|
||||
for (uint16_t i=0;i<psize;i++) {
|
||||
if (parray[i]==pcheck){
|
||||
return false;
|
||||
}
|
||||
}
|
||||
return true;
|
||||
}
|
||||
|
||||
|
||||
|
||||
|
||||
uint16_t getMin(uint16_t *parray, uint16_t psize) {
|
||||
uint16_t min=65535;
|
||||
for (uint16_t i=0;i<psize;i++) {
|
||||
if (parray[i]<min) {
|
||||
min=parray[i];
|
||||
}
|
||||
}
|
||||
|
||||
return min;
|
||||
}
|
||||
|
||||
uint16_t getMax(uint16_t *parray,uint16_t psize) {
|
||||
uint16_t max=0;
|
||||
for (uint16_t i=0;i<psize;i++) {
|
||||
if (parray[i]>max) {
|
||||
max=parray[i];
|
||||
}
|
||||
}
|
||||
|
||||
return max;
|
||||
}
|
||||
|
||||
float getMinf(float *parray, uint16_t psize) {
|
||||
float min=65535;
|
||||
for (uint16_t i=0;i<psize;i++) {
|
||||
if (parray[i]<min) {
|
||||
min=parray[i];
|
||||
}
|
||||
}
|
||||
|
||||
return min;
|
||||
}
|
||||
|
||||
float getMaxf(float *parray,uint16_t psize) {
|
||||
float max=0;
|
||||
for (uint16_t i=0;i<psize;i++) {
|
||||
if (parray[i]>max) {
|
||||
max=parray[i];
|
||||
}
|
||||
}
|
||||
|
||||
return max;
|
||||
}
|
||||
|
||||
|
||||
float getFilteredf(float *parray,uint16_t psize, uint16_t pcutOff) {
|
||||
//cuts off lowest and highest pcutOff values from array, then returns the mean of the psize-2*pcutOff center values.
|
||||
//pcutOff < psize/2
|
||||
|
||||
float _copy[psize];
|
||||
std::copy(parray,parray + psize, _copy);
|
||||
sortArray(_copy,psize);
|
||||
|
||||
double mean=0;
|
||||
for (uint16_t i=pcutOff;i<psize-pcutOff;i++) {
|
||||
mean+=_copy[i];
|
||||
}
|
||||
|
||||
return mean/(psize-2*pcutOff);
|
||||
}
|
||||
|
||||
|
||||
#endif
|
||||
|
|
@ -0,0 +1,131 @@
|
|||
#ifndef _TEMPERATURE_H_
|
||||
#define _TEMPERATURE_H_
|
||||
|
||||
|
||||
#include <OneWire.h>
|
||||
#include <DallasTemperature.h>
|
||||
|
||||
void printAddress(DeviceAddress deviceAddress);
|
||||
|
||||
//first address: 28FF6C1C7216058B
|
||||
//second address:
|
||||
|
||||
#define ONE_WIRE_BUS 18 //GPIO pin
|
||||
#define TEMPERATURE_PRECISION 12 //max is 12
|
||||
#define READINTERVAL_DS18B20 1000 //ms
|
||||
|
||||
// Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs)
|
||||
OneWire oneWire(ONE_WIRE_BUS);
|
||||
|
||||
// Pass our oneWire reference to Dallas Temperature.
|
||||
DallasTemperature sensors(&oneWire);
|
||||
|
||||
|
||||
#define TEMPMEAN_SIZE 16
|
||||
uint16_t tempCmean_pos=0;
|
||||
// arrays to hold device addresses
|
||||
DeviceAddress thermometerReservoir={0x28,0xFF,0x30,0xBA,0x85,0x16,0x03,0xB5};
|
||||
float tempC_reservoir;
|
||||
float tempCmean_reservoir[TEMPMEAN_SIZE];
|
||||
|
||||
DeviceAddress thermometerAir={0x28,0xFF,0x6C,0x1C,0x72,0x16,0x05,0x8B};
|
||||
float tempC_air;
|
||||
float tempCmean_air[TEMPMEAN_SIZE];
|
||||
|
||||
|
||||
void temperature_setup() {
|
||||
|
||||
//initialize mean array
|
||||
for (uint16_t i=0;i<TEMPMEAN_SIZE;i++) {
|
||||
tempCmean_reservoir[i]=-127;
|
||||
tempCmean_air[i]=-127;
|
||||
}
|
||||
|
||||
sensors.begin();
|
||||
delay(1000);
|
||||
|
||||
Serial.print("Locating devices...");
|
||||
Serial.print("Found ");
|
||||
Serial.print(sensors.getDeviceCount(), DEC);
|
||||
Serial.println(" devices.");
|
||||
|
||||
delay(1000);
|
||||
|
||||
Serial.print("Parasite power is: ");
|
||||
if (sensors.isParasitePowerMode()) Serial.println("ON");
|
||||
else Serial.println("OFF");
|
||||
|
||||
delay(1000);
|
||||
|
||||
|
||||
//Just search for devices. Only needed when connecting a new sensor to find the address
|
||||
oneWire.reset_search();
|
||||
|
||||
for (uint8_t i=0;i<sensors.getDeviceCount();i++){
|
||||
DeviceAddress _addr;
|
||||
if (!oneWire.search(_addr)) {
|
||||
Serial.print("Error: Device not found");
|
||||
}else{
|
||||
Serial.print("Found device. Address:");
|
||||
printAddress(_addr);
|
||||
}
|
||||
Serial.println();
|
||||
|
||||
}
|
||||
|
||||
sensors.setResolution(thermometerReservoir, TEMPERATURE_PRECISION);
|
||||
sensors.setResolution(thermometerAir, TEMPERATURE_PRECISION);
|
||||
}
|
||||
|
||||
|
||||
void temperature_loop(unsigned long loopmillis, unsigned long pInterval) {
|
||||
|
||||
static unsigned long last_read_ds18b20;
|
||||
static bool flag_requestTemperatures=false;
|
||||
if (loopmillis>last_read_ds18b20+pInterval) {
|
||||
if (loopmillis>last_read_ds18b20+pInterval*10) { //timeout
|
||||
Serial.println("Warn: Request Temperatures Timeout!");
|
||||
flag_requestTemperatures=false;
|
||||
}
|
||||
if (!flag_requestTemperatures) {
|
||||
sensors.requestTemperatures(); //this takes ~600ms
|
||||
flag_requestTemperatures=true;
|
||||
}
|
||||
if (sensors.isConversionComplete()) {
|
||||
flag_requestTemperatures=false;
|
||||
last_read_ds18b20=loopmillis;
|
||||
|
||||
tempC_reservoir = sensors.getTempC(thermometerReservoir);
|
||||
if (tempC_reservoir == DEVICE_DISCONNECTED_C)
|
||||
{
|
||||
Serial.print(" Error reading: "); printAddress(thermometerReservoir);
|
||||
}else{
|
||||
tempCmean_reservoir[tempCmean_pos]=tempC_reservoir;
|
||||
}
|
||||
|
||||
tempC_air = sensors.getTempC(thermometerAir);
|
||||
if (tempC_air == DEVICE_DISCONNECTED_C)
|
||||
{
|
||||
Serial.print(" Error reading: "); printAddress(thermometerReservoir);
|
||||
}else{
|
||||
tempCmean_air[tempCmean_pos]=tempC_air;
|
||||
}
|
||||
|
||||
tempCmean_pos++;
|
||||
tempCmean_pos%=TEMPMEAN_SIZE;
|
||||
}
|
||||
|
||||
}
|
||||
}
|
||||
|
||||
|
||||
void printAddress(DeviceAddress deviceAddress)
|
||||
{
|
||||
for (uint8_t i = 0; i < 8; i++)
|
||||
{
|
||||
// zero pad the address if necessary
|
||||
if (deviceAddress[i] < 16) Serial.print("0");
|
||||
Serial.print(deviceAddress[i], HEX);
|
||||
}
|
||||
}
|
||||
#endif
|
||||
|
|
@ -0,0 +1,44 @@
|
|||
#ifndef _WATERLEVEL_H_
|
||||
#define _WATERLEVEL_H_
|
||||
|
||||
|
||||
#include <HCSR04.h>
|
||||
#define HCSR04_PIN_ECHO 17
|
||||
#define HCSR04_PIN_TRIGGER 16
|
||||
#define HCSR04_TIMEOUT 5000 //default is 100000 (uS)
|
||||
#define READINTERVAL_HCSR04 100
|
||||
|
||||
#define WATERLEVELMEAN_SIZE 32
|
||||
float waterlevelMean[WATERLEVELMEAN_SIZE];
|
||||
uint16_t waterlevelMean_pos=0;
|
||||
|
||||
|
||||
|
||||
void waterlevel_setup() {
|
||||
|
||||
//HCSR04.begin(HCSR04_PIN_TRIGGER, HCSR04_PIN_ECHO);
|
||||
HCSR04.begin(HCSR04_PIN_TRIGGER, HCSR04_PIN_ECHO,HCSR04_TIMEOUT, HCSR04.eUltraSonicUnlock_t::unlockSkip);
|
||||
for (uint16_t i=0;i<WATERLEVELMEAN_SIZE;i++) {
|
||||
waterlevelMean[i]=-1; //-1 is also timeout value
|
||||
|
||||
}
|
||||
}
|
||||
|
||||
void waterlevel_loop(unsigned long loopmillis, unsigned long pInterval) {
|
||||
|
||||
static unsigned long last_read_hcsr04;
|
||||
if (loopmillis>=last_read_hcsr04+pInterval) {
|
||||
last_read_hcsr04=loopmillis;
|
||||
float temperature=20.0;
|
||||
if (tempC_air!=DEVICE_DISCONNECTED_C && isValueArrayOKf(tempCmean_air,TEMPMEAN_SIZE,DEVICE_DISCONNECTED_C)) { //sensor ok
|
||||
temperature=getMeanf(tempCmean_air,TEMPMEAN_SIZE);
|
||||
}
|
||||
|
||||
double* distances = HCSR04.measureDistanceMm(temperature);
|
||||
|
||||
waterlevelMean[waterlevelMean_pos]=distances[0];
|
||||
waterlevelMean_pos++;
|
||||
waterlevelMean_pos%=WATERLEVELMEAN_SIZE;
|
||||
}
|
||||
}
|
||||
#endif
|
||||
329
src/main.cpp
329
src/main.cpp
|
|
@ -1,71 +1,22 @@
|
|||
#include <Arduino.h>
|
||||
#include <ArduinoSort.h>
|
||||
|
||||
bool flag_print=false;
|
||||
|
||||
#include "helpfunctions.h"
|
||||
|
||||
// ######## EC
|
||||
#define EC_PIN_ADC 4
|
||||
#define EC_PIN_FREQ 5
|
||||
#define EC_PWM_CH 0
|
||||
#define EC_RESOLUTION 8
|
||||
#define EC_FREQUENCY 5000
|
||||
|
||||
#define EC_ARRAY_SIZE 1024
|
||||
uint16_t ec_array[EC_ARRAY_SIZE];
|
||||
uint16_t ec_array_pos=0;
|
||||
unsigned long last_read_ec=0;
|
||||
#define EC_READ_INTERVAL 1
|
||||
#include "ec.h"
|
||||
|
||||
// ######## Temperature
|
||||
#include <OneWire.h>
|
||||
#include <DallasTemperature.h>
|
||||
|
||||
//first address: 28FF6C1C7216058B
|
||||
//second address:
|
||||
|
||||
#define ONE_WIRE_BUS 18 //GPIO pin
|
||||
#define TEMPERATURE_PRECISION 12 //max is 12
|
||||
#define READINTERVAL_DS18B20 1000 //ms
|
||||
|
||||
// Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs)
|
||||
OneWire oneWire(ONE_WIRE_BUS);
|
||||
|
||||
// Pass our oneWire reference to Dallas Temperature.
|
||||
DallasTemperature sensors(&oneWire);
|
||||
|
||||
|
||||
#define TEMPMEAN_SIZE 16
|
||||
uint16_t tempCmean_pos=0;
|
||||
// arrays to hold device addresses
|
||||
DeviceAddress thermometerReservoir={0x28,0xFF,0x30,0xBA,0x85,0x16,0x03,0xB5};
|
||||
float tempC_reservoir;
|
||||
float tempCmean_reservoir[TEMPMEAN_SIZE];
|
||||
|
||||
DeviceAddress thermometerAir={0x28,0xFF,0x6C,0x1C,0x72,0x16,0x05,0x8B};
|
||||
float tempC_air;
|
||||
float tempCmean_air[TEMPMEAN_SIZE];
|
||||
#include "temperature.h"
|
||||
|
||||
|
||||
// ######## Water Level
|
||||
#include <HCSR04.h>
|
||||
#define HCSR04_PIN_ECHO 17
|
||||
#define HCSR04_PIN_TRIGGER 16
|
||||
#define HCSR04_TIMEOUT 5000 //default is 100000 (uS)
|
||||
#define READINTERVAL_HCSR04 100
|
||||
|
||||
#define WATERLEVELMEAN_SIZE 32
|
||||
float waterlevelMean[WATERLEVELMEAN_SIZE];
|
||||
uint16_t waterlevelMean_pos=0;
|
||||
#include "waterlevel.h"
|
||||
|
||||
|
||||
// ######## Flow Rate
|
||||
#define FLOW_PIN 19
|
||||
uint16_t flow_counter=0; //maximum counts/s measured with Eden 128 Pump was 171
|
||||
void IRAM_ATTR isr_flow();
|
||||
unsigned long last_read_flow=0;
|
||||
#define READINTERVAL_FLOW 1000
|
||||
float flow_factor=7.5; //F=7.5*flowrate[L/min]
|
||||
float flow;
|
||||
|
||||
uint32_t flow_counter_sum=0;
|
||||
#include "flow.h"
|
||||
|
||||
|
||||
unsigned long last_print=0;
|
||||
|
|
@ -73,84 +24,22 @@ unsigned long last_print=0;
|
|||
|
||||
|
||||
|
||||
float getMean(uint16_t *parray,uint16_t psize);
|
||||
float getMeanf(float *parray,uint16_t psize);
|
||||
uint16_t getMin(uint16_t *parray, uint16_t psize);
|
||||
uint16_t getMax(uint16_t *parray, uint16_t psize);
|
||||
float getMaxf(float *parray,uint16_t psize);
|
||||
float getMinf(float *parray, uint16_t psize);
|
||||
bool isValueArrayOK(uint16_t *parray,uint16_t psize, uint16_t pcheck);
|
||||
bool isValueArrayOKf(float *parray,uint16_t psize, float pcheck);
|
||||
float getFilteredf(float *parray,uint16_t psize, uint16_t pcutOff);
|
||||
|
||||
|
||||
void printAddress(DeviceAddress deviceAddress);
|
||||
void printTemperature(DeviceAddress deviceAddress);
|
||||
void printResolution(DeviceAddress deviceAddress);
|
||||
void printData(DeviceAddress deviceAddress);
|
||||
|
||||
|
||||
|
||||
|
||||
void setup() {
|
||||
Serial.begin(115200);
|
||||
pinMode(EC_PIN_ADC,INPUT);
|
||||
|
||||
ledcSetup(EC_PWM_CH, EC_FREQUENCY, EC_RESOLUTION);
|
||||
ledcAttachPin(EC_PIN_FREQ, EC_PWM_CH);
|
||||
ledcWrite(EC_PWM_CH, 127);
|
||||
ec_setup();
|
||||
|
||||
//HCSR04.begin(HCSR04_PIN_TRIGGER, HCSR04_PIN_ECHO);
|
||||
HCSR04.begin(HCSR04_PIN_TRIGGER, HCSR04_PIN_ECHO,HCSR04_TIMEOUT, HCSR04.eUltraSonicUnlock_t::unlockSkip);
|
||||
for (uint16_t i=0;i<WATERLEVELMEAN_SIZE;i++) {
|
||||
waterlevelMean[i]=-1; //-1 is also timeout value
|
||||
waterlevel_setup();
|
||||
|
||||
}
|
||||
temperature_setup();
|
||||
|
||||
//initialize mean array
|
||||
for (uint16_t i=0;i<TEMPMEAN_SIZE;i++) {
|
||||
tempCmean_reservoir[i]=-127;
|
||||
tempCmean_air[i]=-127;
|
||||
}
|
||||
|
||||
sensors.begin();
|
||||
delay(1000);
|
||||
|
||||
Serial.print("Locating devices...");
|
||||
Serial.print("Found ");
|
||||
Serial.print(sensors.getDeviceCount(), DEC);
|
||||
Serial.println(" devices.");
|
||||
|
||||
delay(1000);
|
||||
|
||||
Serial.print("Parasite power is: ");
|
||||
if (sensors.isParasitePowerMode()) Serial.println("ON");
|
||||
else Serial.println("OFF");
|
||||
|
||||
delay(1000);
|
||||
|
||||
|
||||
//Just search for devices. Only needed when connecting a new sensor to find the address
|
||||
oneWire.reset_search();
|
||||
|
||||
for (uint8_t i=0;i<sensors.getDeviceCount();i++){
|
||||
DeviceAddress _addr;
|
||||
if (!oneWire.search(_addr)) {
|
||||
Serial.print("Error: Device not found");
|
||||
}else{
|
||||
Serial.print("Found device. Address:");
|
||||
printAddress(_addr);
|
||||
}
|
||||
Serial.println();
|
||||
|
||||
}
|
||||
|
||||
sensors.setResolution(thermometerReservoir, TEMPERATURE_PRECISION);
|
||||
sensors.setResolution(thermometerAir, TEMPERATURE_PRECISION);
|
||||
|
||||
|
||||
pinMode(FLOW_PIN, INPUT_PULLUP);
|
||||
attachInterrupt(FLOW_PIN, isr_flow, CHANGE);
|
||||
flow_setup();
|
||||
|
||||
Serial.println("Setup finished");
|
||||
delay(500);
|
||||
|
|
@ -159,86 +48,20 @@ void setup() {
|
|||
void loop() {
|
||||
unsigned long loopmillis=millis();
|
||||
|
||||
bool flag_print=false;
|
||||
flag_print=false;
|
||||
|
||||
|
||||
|
||||
if (loopmillis>last_read_ec+EC_READ_INTERVAL) {
|
||||
last_read_ec=loopmillis;
|
||||
ec_array_pos++;
|
||||
flag_print= ec_array_pos==EC_ARRAY_SIZE;
|
||||
ec_array_pos%=EC_ARRAY_SIZE;
|
||||
ec_array[ec_array_pos]=analogRead(EC_PIN_ADC);
|
||||
|
||||
//Serial.print(ec_array[ec_array_pos]); Serial.print(" ");
|
||||
}
|
||||
ec_loop(loopmillis, EC_READ_INTERVAL);
|
||||
|
||||
|
||||
static unsigned long last_read_ds18b20;
|
||||
static bool flag_requestTemperatures=false;
|
||||
if (loopmillis>last_read_ds18b20+READINTERVAL_DS18B20) {
|
||||
if (loopmillis>last_read_ds18b20+READINTERVAL_DS18B20*10) { //timeout
|
||||
Serial.println("Warn: Request Temperatures Timeout!");
|
||||
flag_requestTemperatures=false;
|
||||
}
|
||||
if (!flag_requestTemperatures) {
|
||||
sensors.requestTemperatures(); //this takes ~600ms
|
||||
flag_requestTemperatures=true;
|
||||
}
|
||||
if (sensors.isConversionComplete()) {
|
||||
flag_requestTemperatures=false;
|
||||
last_read_ds18b20=loopmillis;
|
||||
|
||||
tempC_reservoir = sensors.getTempC(thermometerReservoir);
|
||||
if (tempC_reservoir == DEVICE_DISCONNECTED_C)
|
||||
{
|
||||
Serial.print(" Error reading: "); printAddress(thermometerReservoir);
|
||||
}else{
|
||||
tempCmean_reservoir[tempCmean_pos]=tempC_reservoir;
|
||||
}
|
||||
|
||||
tempC_air = sensors.getTempC(thermometerAir);
|
||||
if (tempC_air == DEVICE_DISCONNECTED_C)
|
||||
{
|
||||
Serial.print(" Error reading: "); printAddress(thermometerReservoir);
|
||||
}else{
|
||||
tempCmean_air[tempCmean_pos]=tempC_air;
|
||||
}
|
||||
|
||||
tempCmean_pos++;
|
||||
tempCmean_pos%=TEMPMEAN_SIZE;
|
||||
}
|
||||
|
||||
}
|
||||
temperature_loop(loopmillis, READINTERVAL_DS18B20);
|
||||
|
||||
|
||||
waterlevel_loop(loopmillis, READINTERVAL_HCSR04);
|
||||
|
||||
|
||||
static unsigned long last_read_hcsr04;
|
||||
if (loopmillis>=last_read_hcsr04+READINTERVAL_HCSR04) {
|
||||
last_read_hcsr04=loopmillis;
|
||||
float temperature=20.0;
|
||||
if (tempC_air!=DEVICE_DISCONNECTED_C && isValueArrayOKf(tempCmean_air,TEMPMEAN_SIZE,DEVICE_DISCONNECTED_C)) { //sensor ok
|
||||
temperature=getMeanf(tempCmean_air,TEMPMEAN_SIZE);
|
||||
}
|
||||
flow_loop(loopmillis, READINTERVAL_FLOW);
|
||||
|
||||
double* distances = HCSR04.measureDistanceMm(temperature);
|
||||
|
||||
waterlevelMean[waterlevelMean_pos]=distances[0];
|
||||
waterlevelMean_pos++;
|
||||
waterlevelMean_pos%=WATERLEVELMEAN_SIZE;
|
||||
}
|
||||
|
||||
|
||||
static uint16_t _last_flowconter; //for debugging
|
||||
if (loopmillis>=last_read_flow+READINTERVAL_FLOW) {
|
||||
flow=flow_counter*1000.0/(loopmillis-last_read_flow)/2.0; //Frequency [Hz]
|
||||
flow/=flow_factor; //[L/min]
|
||||
_last_flowconter=flow_counter; //for debugging
|
||||
|
||||
flow_counter=0;
|
||||
last_read_flow=loopmillis;
|
||||
}
|
||||
|
||||
|
||||
if (loopmillis>last_print+500) {
|
||||
|
|
@ -274,7 +97,7 @@ void loop() {
|
|||
Serial.print("\t waiting for distance");
|
||||
}
|
||||
|
||||
Serial.print("\t Flow="); Serial.print(flow,2); Serial.print(" ("); Serial.print(_last_flowconter); Serial.print(")");
|
||||
Serial.print("\t Flow="); Serial.print(flow,2);
|
||||
Serial.print("\t Flowsum="); Serial.print(flow_counter_sum);
|
||||
|
||||
|
||||
|
|
@ -284,119 +107,3 @@ void loop() {
|
|||
}
|
||||
|
||||
}
|
||||
|
||||
float getMean(uint16_t *parray,uint16_t psize) {
|
||||
double mean=0;
|
||||
for (uint16_t i=0;i<psize;i++) {
|
||||
mean+=parray[i];
|
||||
}
|
||||
|
||||
return mean/psize;
|
||||
}
|
||||
float getMeanf(float *parray,uint16_t psize) {
|
||||
double mean=0;
|
||||
for (uint16_t i=0;i<psize;i++) {
|
||||
mean+=parray[i];
|
||||
}
|
||||
|
||||
return mean/psize;
|
||||
}
|
||||
|
||||
bool isValueArrayOK(uint16_t *parray,uint16_t psize, uint16_t pcheck) { //check if array has error values
|
||||
for (uint16_t i=0;i<psize;i++) {
|
||||
if (parray[i]==pcheck){
|
||||
return false;
|
||||
}
|
||||
}
|
||||
return true;
|
||||
}
|
||||
bool isValueArrayOKf(float *parray,uint16_t psize, float pcheck) { //check if array has error values
|
||||
for (uint16_t i=0;i<psize;i++) {
|
||||
if (parray[i]==pcheck){
|
||||
return false;
|
||||
}
|
||||
}
|
||||
return true;
|
||||
}
|
||||
|
||||
|
||||
|
||||
|
||||
uint16_t getMin(uint16_t *parray, uint16_t psize) {
|
||||
uint16_t min=65535;
|
||||
for (uint16_t i=0;i<psize;i++) {
|
||||
if (parray[i]<min) {
|
||||
min=parray[i];
|
||||
}
|
||||
}
|
||||
|
||||
return min;
|
||||
}
|
||||
|
||||
uint16_t getMax(uint16_t *parray,uint16_t psize) {
|
||||
uint16_t max=0;
|
||||
for (uint16_t i=0;i<psize;i++) {
|
||||
if (parray[i]>max) {
|
||||
max=parray[i];
|
||||
}
|
||||
}
|
||||
|
||||
return max;
|
||||
}
|
||||
|
||||
float getMinf(float *parray, uint16_t psize) {
|
||||
float min=65535;
|
||||
for (uint16_t i=0;i<psize;i++) {
|
||||
if (parray[i]<min) {
|
||||
min=parray[i];
|
||||
}
|
||||
}
|
||||
|
||||
return min;
|
||||
}
|
||||
|
||||
float getMaxf(float *parray,uint16_t psize) {
|
||||
float max=0;
|
||||
for (uint16_t i=0;i<psize;i++) {
|
||||
if (parray[i]>max) {
|
||||
max=parray[i];
|
||||
}
|
||||
}
|
||||
|
||||
return max;
|
||||
}
|
||||
|
||||
|
||||
|
||||
|
||||
void printAddress(DeviceAddress deviceAddress)
|
||||
{
|
||||
for (uint8_t i = 0; i < 8; i++)
|
||||
{
|
||||
// zero pad the address if necessary
|
||||
if (deviceAddress[i] < 16) Serial.print("0");
|
||||
Serial.print(deviceAddress[i], HEX);
|
||||
}
|
||||
}
|
||||
|
||||
|
||||
void IRAM_ATTR isr_flow() {
|
||||
flow_counter++;
|
||||
flow_counter_sum++;
|
||||
}
|
||||
|
||||
float getFilteredf(float *parray,uint16_t psize, uint16_t pcutOff) {
|
||||
//cuts off lowest and highest pcutOff values from array, then returns the mean of the psize-2*pcutOff center values.
|
||||
//pcutOff < psize/2
|
||||
|
||||
float _copy[psize];
|
||||
std::copy(parray,parray + psize, _copy);
|
||||
sortArray(_copy,psize);
|
||||
|
||||
double mean=0;
|
||||
for (uint16_t i=pcutOff;i<psize-pcutOff;i++) {
|
||||
mean+=_copy[i];
|
||||
}
|
||||
|
||||
return mean/(psize-2*pcutOff);
|
||||
}
|
||||
Loading…
Reference in New Issue