Commit Graph

25 Commits

Author SHA1 Message Date
Candas1 d7880dafeb
Update util.c 2020-10-27 20:44:52 +01:00
Candas1 09b2728168
Update util.c 2020-10-27 20:38:19 +01:00
Candas1 5d954a05aa
Fix typo 2020-10-27 20:24:56 +01:00
Candas1 0ab8e8e5ac
Improve adddeadband function
- Use MAP function
- add additional parameter for middle value
- use adddeadband function with ADC input when mid resting pot is used
2020-10-27 19:39:12 +01:00
EmanuelFeru 4fbf2549c9 Cruise Control update
- added support for Cruise Control in HOVERCAR variant
- updated the shortBeep function, didn't like the beeping sound :)
2020-10-20 19:54:38 +02:00
EmanuelFeru 8369e4d47d Increased delay for CC
In Cruise Control (CC), the button can bounce. The beep delay is increased from 100ms to 200ms to prevent button bouncing and continuous activation/deactivation of CC.
2020-10-13 10:38:43 +02:00
EmanuelFeru 66857b5680 Fixed symbol 2020-10-13 08:58:42 +02:00
EmanuelFeru b76e8ee466 Update BLDC controller
- added possbility to switch the Control mode while motor is spinning. NOT yet checked how motors behaves when swiching is triggered!
- added Cruise Control functionality: activated by button1 to GND (Blue Left or Right cable depending on selection). Functionality NOT yet tested in practice!
- extended Phase current measurements z_selPhaCurMeasABC : {iA,iB} = 0; {iB,iC} = 1; {iA,iC} = 2
- added interface for external motor angle measurement from as sensor, e.g., encoder. The selection can be done via b_angleMeasEna: 0 = Estimated (default), 1 = Measured.
- update the Field weakening Lo and Hi to fully blended.
- minor improvements:
   - Buttons initialization
   - lowered ADC margins in auto-calibration
   - commented out ADC_SAMPLETIME_239CYCLES_5, reported to give some issues when Hall sensor ADC input is used
2020-10-12 22:55:39 +02:00
EmanuelFeru 733fd80362 created SKATEBOARD variant 2020-07-20 20:33:42 +02:00
EmanuelFeru dcdac4f6db Updated PWM variant
- fixed the setScopeChannel for PWM, to calibrate properly the limits
- improved the scaling
2020-07-20 19:36:24 +02:00
EmanuelFeru f2d86f3b30 Added functionality: Electric Brake, Standstill hold
- For TORQUE mode, by enabling `ELECTRIC_BRAKE_ENABLE` in `config.h`, the freewheeling amount can be adjusted using the `ELECTRIC_BRAKE_MAX` parameter.
- For VOLTAGE and TORQUE mode, the standstill hold functionality can be forced by enabling `STANDSTILL_HOLD_ENABLE` in `config.h`.

Known (minor) issue: There is a small "tick" noise when Stanstill is engaged/disengaged, due to the switching to SPEED mode. To be solved by an improved mode switching strategy in the future.
2020-07-19 11:24:37 +02:00
EmanuelFeru 22984a7fd6 Fixed PPM, PWM timeout
- fixed the general timeout handling: there is no need to disable the MOSFETs timer because it will confuse the BLDC_controller, making him consider the timeout as a false MOSFET defective error.
- renamed `timeout` to `timeoutCnt` for consistency and to ease the search
#61
2020-07-01 19:50:32 +02:00
EmanuelFeru 68776699e1 Updated Mid resting poti scaling
Issue #74
2020-06-30 18:09:37 +02:00
EmanuelFeru 17e127a8b7 PWM/PPM Left/Right, UART update
- created possiblity to use PWM, PPM input also on both LEFT and RIGHT cable (RIGHT cable is 5V tolerant)
- updated UART: disabled the Rx errors to avoid DMA stop and additional need to manage the UART error handler
- added Button support LEFT/RIGHT
2020-06-25 20:17:55 +02:00
EmanuelFeru 5f2eb196af Improved UART error recovery
- In case of an Rx error instead of stopping the complete UART, only the Rx DMA is aborted and restarted.
2020-06-23 19:58:36 +02:00
EmanuelFeru ac90ed1b6b Fixed initial condition bug
- the initial condition for the Battery and Board temperature was wrongly set
- the filter is fixdt(1,32,16), so the shift should be by 16 bits.
2020-06-22 20:21:18 +02:00
EmanuelFeru b8d9c8c8bc Re-arranged variables
- no functionality change
2020-06-22 09:17:42 +02:00
EmanuelFeru e46dff590f Major UART communication improvement
- the UART communication is improved based on UART Idle line detection interrupt
- an Rx ring buffer is used to manage the UART incoming data
- both Tx and Rx are efficiently handled using DMA

#45 #64 #65

Other:
- minor visual improvements
2020-06-21 23:14:46 +02:00
EmanuelFeru 34c6e4d610 Improved UART Timeout
Apparently, the UART data Rx/Tx is quite unreliable (especially under motor load) leading to very often out-of-sync issues. This change allows to reset the DMA more often, leading to a faster re-sync of the UART transmission and thus avoiding UART timeout.
2020-06-01 20:08:47 +02:00
EmanuelFeru 95c10c9ba7 Update util.c 2020-03-24 21:31:30 +01:00
EmanuelFeru 38574153f0 Added deadband for PPM signal
Issue #29
2020-03-24 20:36:19 +01:00
EmanuelFeru 39e4fdc869 Variant_PWM implemented 2020-03-24 19:57:08 +01:00
EmanuelFeru c099bec824 RC pwm signal read fixes
Re-work on the RC pwm input signal timeout
2020-03-23 21:09:17 +01:00
EmanuelFeru 7d80e564f0 First commit pwm
- buttons not yet support
2020-03-21 19:24:29 +01:00
EmanuelFeru 72e6b30033 UART with sideboards works + major refactoring
► the mainboard can now send and receive Serial data from the sideboards
► heavy refactored the `main.c`. It was becoming too large to manage... Therefore, `util.c` and `util.h` was created
► added new functionality for `VARIANT_HOVERCAR` and variants with `CONTROL_ADC` in general:
- ADC limits auto-calibration mode (long press of the power button) - calibration will not be lost at power-off
- Max Current and Max Speed adjustment mode (long press followed by a short press of the power button) - calibration will not be lost at power-off
- added one sideboard functionality:
         - LEDs are used to display battery level,  Motor Enable, Errors, Reverse driving, Braking.
         - Photo sensors are used as push buttons: One for changing Control Mode, One for Activating/Deactivating the Field Weakening on the fly
2020-03-01 10:00:26 +01:00